3D Model Gallery
Every one of these started as a sentence — real dimensions, real holes, print-ready STL. Remix any of them, or describe the part you need and Printy builds it. Start building →
Newest
Basic Geometry Block Set
What it's for A complete set of foundational geometry blocks for educational and mathematical demonstration. Designed to sit uniformly flat on the build plate. Dimensions Bounding limits: All pieces are scaled to fit within or align with a 100x100x100 mm (10x10x10 cm) overall volume. Shapes included: Cube (100mm uniform), Square Prism (60x60x100mm), Rectangular Prism (100x60x40mm), Triangular Prism, Cylinder, Cone, and Sphere. Print notes The sphere prints best with a small brim to ensure adhesion, though its bottom is anchored exactly at z=0. No supports are needed for the upright pieces.
Bedside Book and Bottle Caddy
A heavy-duty bedside caddy built to hang over a standard 20 mm bed rail. Keeps reading material, a water bottle, and a phone separated and off the nightstand. The hook arms are braced internally with steep-angled ribs so the entire assembly prints without supports, and the bottle pocket includes a bottom drain to stop condensation from pooling. Fitment: 23 mm hook gap for standard 20 mm bed frames Book Slot: 167 mm wide by 84 mm deep Bottle Holder: 88 mm internal diameter with drain Phone Slot: 30 mm wide, isolating electronics from the bottle Material: Optimized for PETG with 3 mm minimum walls
16-Inch Open Top Trash Can
A standard open-top waste bin dimensioned for specific clearance requirements. The base and vertical edges are rounded to prevent stress concentrations and make the interior easy to wipe down. Specifications Overall Dimensions: 16" H × 9.5" W × 10" L (406 × 241 × 254 mm) Wall Thickness: 3 mm Edge Treatment: 15 mm exterior rounding, 12 mm interior rounding
2" Reinforced Press Weight
A solid block with a thin handle usually ends up as a broken handle and a block you can't lift. This 5-inch heavy press cylinder avoids the snapping point entirely by heavily radiusing the base of the handle where it takes the most sheer stress. Critical Dimensions Base block: 5" diameter (127 mm), 2" thick (50.8 mm). Handle: 1" diameter (25.4 mm), extending 3" above the base. Hanging hole: 0.5" diameter (12.7 mm). All exterior edges are rounded with a 3mm radius to prevent chipping.
Cable organizer box with Unifi AP Lid
Our coworking space needs some cables organized on top of the kitchen cabinets. V1, not tested yet, so print at your own risk!
Dog Remote Belt Holster 3
Fumbling for the remote when you actually need it defeats the point of having one. This holster locks the transmitter to your belt so it stays exactly where your hand expects it to be. The front channel leaves the main buttons clear to press without drawing the remote, and the bottom cutout lets you push it up easily when you do need it. Fit Details Sleeve Dimensions: Fits bodies up to 34 mm wide and 28 mm thick. Clip Capacity: Fits belts up to 45 mm (1.75 inches) wide and 6 mm thick. Printing: Print standing upright. PETG is strongly recommended over PLA so the belt clip has enough flex to snap over your belt without snapping off.
4-Inch Block with Hanging Grip
A 4-inch diameter, 2-inch thick solid cylinder block equipped with a 1-inch vertical grip. Built with fully radiused edges to prevent chipping during heavy use. The handle includes a 3/8-inch cross-hole near the top, sized to clear standard pegboard hooks, nails, or a paracord lanyard for hanging storage. Check your hook diameter if you're mounting this on a custom rack. Base Footprint: 4" OD × 2" H Handle Dimensions: 1" OD × 2.5" H (above base) Hole Clearance: 3/8" bore
Cylinder Weight With Post
What it's for A heavy cylindrical base with an extended center post, designed to act as a tether point, weight, or hanging anchor in the workshop. Dimensions Base: 4 inches (101.6 mm) diameter, 2 inches (50.8 mm) tall. Post: 1 inch (25.4 mm) diameter, extending 3 inches (76.2 mm) above the base. Hole: 0.4 inches (10 mm) diameter, positioned near the top of the post for rigging lines or carabiners. Materials Print with dense infill (at least 60%) if being used as a counterweight. PETG or ABS is recommended for impact resistance.
3-Inch Tool with Handle
A heavy-duty pounding or tamping tool, dimensioned strictly to a 3-inch diameter base and a 1-inch diameter grip. Dimensions to Check Base Profile: 3.0" OD x 2.0" Height Grip Profile: 1.0" OD x 3.0" Height Hanger Hole: 0.375" (3/8") through-bore centered 0.5" from the top of the handle. Prints flat on the base. Requires no supports.
Oversized Bureaucratic Desk Stamp
A massive, monolithic pressing base capped with a classic flared grip. It has the proportions of heavy bureaucratic machinery, built to lay down serious, even pressure across a large surface. Press Details Base Dimensions: 4-inch diameter footprint by 2 inches thick. Handle: Gently flared vertical grip with a rounded top for comfortable palm pressure. Edges: Lightly chamfered base prevents elephant's foot and avoids marring whatever is being pressed.
CardBlank — 5-Ply Token
A solid rectangular token matching the exact footprint of a standard poker playing card (2.5 x 3.5 inches), extruded to the thickness of five standard cards (1.5 mm). Ideal for use as a deck spacer, a durable proxy blank, or a dimensional template for designing custom card accessories. The corners feature a standard 3 mm radius cut to match commercial playing cards. Dimensions Width: 63.5 mm (2.5 in) Height: 88.9 mm (3.5 in) Thickness: 1.5 mm (approx. 5 standard cards) Corner Radius: 3 mm
Aero H-Frame Brushless Motor Stand
Bu parça, fırçasız (brushless) drone motorlarının itme gücünü (thrust) güvenle test edebilmeniz için tasarlanmış statik bir tezgah standıdır. Gövdesi itme kuvvetine karşı esnememesi için arka destek takozuyla güçlendirilmiş H profilli bir tabandan oluşur. Modüler Yapı: Motorun takıldığı ön plaka ana gövdeden bağımsızdır. Şu anki plaka 9mm BCD ve 4 adet M2 vida formatına uygun; ileride farklı motorlar için sadece plakayı değiştirerek kullanmaya devam edebilirsiniz. Boyut ve İzinler: Motor ekseni zeminden 90mm yüksekte konumlandırılmıştır. 80mm çapındaki pervaneleriniz tabana çarpmadan rahatça çalışabilir. Sabitleme: Alt kısımdaki ayaklarda tezgahınıza veya ağır bir ahşap bloğa vidalamanız için 4 adet havşalı M4 delik bulunur. Test güvenliği için standı mutlaka zemine sabitleyin.
9mm PCD Brushless Motor Stand
A clean, streamlined static test mount for brushless electric drone motors. Elevates the motor to provide ample clearance for 80mm propellers while keeping the mass low and the profile minimal. Technical Details Motor Fitment: Designed for a 9mm pitch-circle diameter (PCD) using four M2 bolts. Propeller Clearance: Center height is positioned to comfortably clear an 80mm diameter prop. Mounting Setup: Employs a slim 4mm mounting face, eliminating the need for bulky access tunnels. M2 fasteners can pass straight through from the back. Base Plate: Features an extended footprint with M5 clearance holes for secure fastening to a test bench.
Sentinel Deck Vault
A robust, two-piece deck box built for transport and easy access. Designed to hold 100 double-sleeved 63x88mm trading cards, it features a snug snap-fit lid to prevent spills in your bag. Secure Closure: Friction-fit lip with spherical snap detents. Easy Access: Deep thumb cutouts on the front and back let you grab the whole deck at once. Sturdy Build: Thick 2.4mm outer walls for solid protection.
Classic Stacking Ring Toy
A classic educational stacking ring set designed for early motor skills. The design features thick, fully rounded components to eliminate sharp edges and ensure safe handling. The generous clearances make stacking easy for small hands. What it's for Perfect as a robust, classic nursery toy or a personalized gift for a toddler. It teaches size sorting and hand-eye coordination. Dimensions Overall Height: 130 mm Base Plate: 100 mm diameter Stacking Rings: 85 mm, 70 mm, and 55 mm outer diameters Internal Clearances: 1.5 mm gap between the post and the rings to prevent binding. Print notes Print the rings and base separately on their flat bottom faces. Use a high infill for the base to give the toy a low center of gravity. No supports are required for any of the parts.
Stepped Makeup Organizer With Tilting Mirror test 1
A multi-tier storage organizer designed for makeup, cosmetics, and brushes. It features a stepped compartment layout, dedicated grid slots for lipsticks, and hinged lids with simple opening tabs to keep stored items dust-free. The back incorporates mortise slots that accept two upright supports. These supports hold a tilting mirror frame designed to accept a standard acrylic or real mirror sheet. Assembly Notes The parts are laid out flat on the build plate for support-free FDM printing. Uses modular drop-in supports to mount the mirror frame. The main body features integrated hinge knuckles; the lids attach using the included printable pivot pins. Clearances are set to 0.4 mm for smooth hinge rotation directly off the printer.
Tokens 3d print
A 3D-printable card dispenser built for standard playing cards. The stack sits vertically, and a narrow 0.8 mm slot at the bottom front lets exactly one card pass through at a time, stripping off any cards that try to follow it. Features a sliding track cutout in the floor for your thumb, and rests on 25 mm legs so you can pull a card without lifting the box off the table. A friction-fit lid keeps the rest of the deck secure. Holds one standard 40 mm stack of cards Bottom-dispensing slot (one card at a time) 25 mm elevated base for table-top access No supports required
Track-Ready Kart Frame
A half-meter-long go-kart frame complete with a full racing loadout. The chassis features lightweight cutouts along the floor pan and thick side pods for impact resistance, while the cockpit sports a contoured racing seat with aggressive side bolsters to keep the driver planted. Out back, a finned engine block feeds twin rear-facing exhaust pipes. Key Features Chassis Design: Extended floor pan with weight-reduction cutouts and integrated side pods. Racing Seat: Deeply contoured base and backrest with prominent side bolsters. Steering: Three-spoke wheel mounted on an angled column with a solid base support. Powerplant: Rear-mounted block engine featuring cooling fins and dual exhausts. Wheels: Rounded tires with defined center hubs mounted on robust solid axles.
Mason Jar Fly Trap Lid
Leaving a bowl of vinegar on the counter just means you eventually knock over a bowl of vinegar. This insert replaces the flat lid in a canning ring to turn any jar into a one-way trap Diameter: 84 mm (fits the ring). Depth: 35 mm funnel projection into the jar. Exit Aperture: 4 mm (wide enough to enter, too narrow to navigate back). Printability: The flat face sits on the bed. The funnel tapers upward. Zero supports needed.
Cinematic Webbed Face Shell
A cinematic-style face shell featuring aggressive eye frames and a full raised webbing pattern across the surface. The webbing radiates from the bridge of the nose for that classic screen-accurate look. Webbing: 1.5 mm raised lines, intersecting in a radial pattern. Frames: 4 mm thick, stepped out slightly past the webs. Scale: Sized generally for display, but the scaling parameters in the shell module are the ones to tweak if you're trying to match it to a specific bust or head form.
Teardrop Sticker Dispenser
A compact, teardrop-shaped dispenser designed specifically for sticker rolls. The two halves snap together smoothly to fully enclose the roll, protecting the stickers and keeping the tape aligned. Design Details Capacity: Fits rolls up to 95mm outer diameter and 16mm width. Interlock: 5mm deep stepped lip with a 0.3mm radial clearance for a secure, tool-free friction fit right off the bed. Walls: 4mm thick for rigidity, stepping down seamlessly into the inner cavity. Exit: A simple 18mm front slot lets the tape pull freely without snagging. Both halves print flat on their outer faces without supports. If you find the friction fit too tight or too loose on your printer, the clearance parameter is the first thing to adjust.
Teardrop Sticker Roll Dispenser
Un boîtier distributeur pour rouleaux de gommettes de 13 mm (mandrin de 76 mm). La forme en goutte épouse le rouleau et guide la bande vers une ouverture fine. Conception en deux pièces : Un corps principal et un couvercle qui s'emboîte par simple friction. Sortie de précision : Une fente étroite de 2 mm avec des dents intégrées pour déchirer la bande proprement. Impression optimisée : Conçu pour s'imprimer à plat sans aucun support.
Distributeur de Gommettes Sport Tir
Boîte de distribution verticale dimensionnée sur mesure pour accueillir librement un rouleau de gommettes de 98 mm. Le rouleau repose par gravité, distribuant les autocollants via une fente frontale affleurante. Détails de conception Fente ajustée : 18 mm de large pour guider précisément un rouleau de 16 mm. Typographie en relief : Inscription latérale robuste dépassant de 0,7 mm. Mécanisme sans axe : Le rouleau tourne naturellement contre les parois internes. Couvercle à glissière : Insertion par l'arrière avec un ergot de verrouillage tactile et une prise en relief.
tapbay pillar stand
A tabletop pillar sign featuring vertically stacked text protruding prominently from the front and back faces. Vertical text layout: Letters run top to bottom down a straight central post. Double-sided: Readable from both the front and back faces. Heavy embossing: Text extrudes outwards for a bold, dimensional look. Stable base: A low-profile chamfered circular base keeps the pillar steady.
Need a part that doesn't exist yet?
Start building →