3D-printable decor & display pieces
Lithophane shades, planters, trophies, wall art and display models. Browse what makers built, or describe the exact piece you want and Printy makes it.
Need one that fits your exact measurements? Start building →
Newest
Moldura de Parede A4 com Gancho
Moldura de parede para folha A4 com gancho em J fechado na borda inferior e suporte para prego escondido no verso. A folha desliza pela abertura no topo e fica num rebaixo atrás da janela. O gancho tem a aba de retorno voltada para a moldura, formando uma abertura fechada. O suporte com furo de fechadura fica na parte de trás, no topo, e não aparece de frente. Moldura externa: 240 x 327 mm Janela: 196 x 283 mm Gancho em J: 16 mm de largura, 24 mm de altura Suporte de prego: aba traseira de 4 mm com furo de fechadura
Doll Wardrobe With Opening Doors
Doll wardrobe whose doors stay shut and never swing, because they are glued-on slabs. This one has two doors on pin hinges that actually open, with a centre divider and a hanging rail inside. Key numbers Overall size: 200 mm long x 50 mm deep x 200 mm high Walls and shelves: 6 mm; back panel 4 mm Doors: 4 mm thick, sit flush in the front opening with 0.6 mm clearance Hinge pins: 3 mm, in 3.8 mm sockets in the top and bottom panels Hanging rail: 5 mm round bar, 30 mm below the top Printing Print the body upright, open front facing you. Print the doors standing on their long edge, pins pointing up and down; pin ends need no supports. Drop each door's lower pin into its socket first, then tilt the top pin in. Rail and knobs are separate pieces to print and glue in place.
Lamp Bases, Shades and Diffuser Set
A set of mid-century lamp parts that all share one coarse 6 mm-pitch thread, so any shade fits any base. The set has two fluted shades (round and square ribs), a white adjustable diffuser and several bases: tall, short, grooved, two tripods, a flat-leg grooved tripod and a dowel-leg hub. Remix hooks Flat-leg tripod: legs are 16 mm wide slabs (before scaling) with two grooves, 3.2 mm wide, down each outer face. Change the groove count, offset (±4 mm) or width. Leg height and spread: hub height 70 mm and foot radius 70 mm set the splay. Raise both for a taller version. Thread spigot: 52 mm across, 38 mm long. Keep it to stay compatible with the shades. Pairs with: either fluted shade and the diffuser. The 42 mm bore runs straight through for the bulb and cord.
Teardrop Lamp Parts, Terracotta and Wood
A mid-century teardrop table lamp laid out as separate print pieces: fluted base, threaded crown collar, hollow prolate-spheroid diffuser and three dovetail-cleat prongs. A second set of the base, crown and prongs is included in a walnut-style wood tone, so one diffuser works with either finish. Remix hooks Wood finish: the wood set is the same geometry in a different colour. Print it in wood-fill or walnut-toned filament, then sand and oil it. Real grain would need a textured surface, which is a good next step. Fit: the thread clearance is about 0.4 mm and the cleat clearance about 0.3 mm. Adjust these to suit your printer. Bulb: it is sized for a 127 mm T10 or an ST19. The crown bore is 31 mm and the diffuser opening is 36.5 mm. Pairs with: an E26 socket, plus a small glue dab or set screw if you want the cleats locked. The tallest piece, a prong, is about 203 mm, so everything fits a 256 mm bed.
Mandarin Town — Colorful Community Scene
A bright miniature town for learning Mandarin community vocabulary. Each building carries its name in Chinese, pinyin and English, and every main building has its own wall colour. Signs, a park, a pond, houses, cars and people fill out the scene. Features Hospital, library, community center, store and school, each in a different colour Park with pond, benches and trees, plus a banner reading 一起参加活动 Road with cars, footpaths, lamps and neighbourhood houses Work and Service signs with people at the buildings Dimensions 200 × 200 mm base plate, 4 mm thick
Mandarin Community Town Model
A tabletop town for practising Mandarin place words, where flat labels get lost. Each building, sign and park area carries its Chinese characters, pinyin and English on the front face, so the vocabulary sits right on the thing it names. Details that matter Base: 200 × 200 mm, 4 mm thick plate Buildings: hospital, library, community center, store and school, each 46 × 28 mm footprint Extras: park with pond, road, footpaths, houses, cars, trees, lamps and figures Colour regions: ground, road, walls, roofs, doors, lettering, signs, trees, lawn, pond, paths Print: large bed needed (or scale down); multicolour or paint by region; lettering is 0.8 mm raised, so use a 0.4 mm nozzle
Mandarin Community Town Model
What it's for A small-town community model for a Mandarin class project. Each facility carries a Chinese, pinyin and English label, and the action words appear on signs, a banner and people scenes. Dimensions Base: 200 × 200 mm, 4 mm thick Buildings: 46 × 28 mm, 32 mm tall Labelled places: 医院, 图书馆, 社区中心, 商店, 学校, 公园 Action words: 工作 and 服务 on signs, 一起参加活动 on the park banner, with people grouped together Extras: road, paths, trees, houses, cars, benches, streetlights, neighbours Remix ideas Add more houses with 邻居 labels Swap the school for another facility Print in several colours to paint or assemble per group
Elipsa
Izduženi ovalni okvir u obliku glatke kontinuirane trake, širine 80 mm, kao elegantna orbita bez ikakvog teksta unutra. Donji luk je širi i izraženiji od ostatka, a cijela traka leži na ploči, bez dijelova koji vise u zraku. Visina gornjeg i bočnog dijela: 0,8 mm Visina donjeg luka: 1,8 mm Širina trake: 2,4 mm, a na donjem luku 3,8 mm Ravna baza, prilagođena FDM štampi
Eiffelturm-Gitter auf Klemmring
Ein filigraner Gitterkorb auf vier nach innen geknickten Pfosten, die an eine Eiffelturm-Silhouette erinnern. Unten sitzt ein Klemmring für Zylinder mit 73 mm Durchmesser. Gesamthöhe ca. 54 mm Klemmring 12 mm hoch, mit Schlitz und M4-Querbohrung Vier Pfosten enden unten am Korb Korb aus Stäben und Ringen
Electronics Box With Solar Panel
A wildlife alert electronics box with a tilted solar panel on top, and no post or base to tip over. The box sits flat on the table, and its two front holes stay stacked on one centre line. Box: 110 × 70 × 60 mm, 3 mm walls, lid held by four screws Front holes: 5.2 mm amber LED above a 24 mm PIR sensor opening Solar panel: 110 × 100 mm at 30°, on two printed brackets Printing: FDM, no supports needed for the lid; print the box with its open back facing up
Watch Bracelet Mid-Link 14 x 31 mm
Replacement mid-link for a metal watch bracelet, 14 mm wide and 31 mm long, with a crowned top, a forked female hinge end and a single-tongue male hinge end. Pin holes are 1.6 mm for reaming. The underside is pocketed to save material. Body: 14.0 x 31.0 x 3.4 mm, 1.4 mm edge fillets Crown: raised 0.8 mm above the body top Female end: two 5.2 mm diameter ears, 5.2 mm slot Male end: 4.6 mm diameter tongue, 4.4 mm wide Pin holes: 1.6 mm, at Y = ±17.9 (35.8 mm pin to pin) Underside pocket: 1.9 mm deep, 0.7 mm corner radius Wrist curve not applied; exported flat Intended for PETG, printed bottom face down
Posable Dragon With Friction Joints
A posable toy dragon that holds its pose, with detailing so it doesn't look like a plain chain of balls. The old version looked like a bare stick of linked beads. This one adds belly plates, scale studs and a trimmed base. What's on it Cream belly plates under each body link Dark-red scale studs along both flanks, plus the back spike row Raised gold trim around the edge of the base Same 12 ball-jointed body links and ball-jointed head Print notes 0.2 mm joint clearance: raise it if the joints fuse, lower it if they sag Print in PETG for repeated bending Multi-colour print or paint the belly plates, trim and spikes
Pad Plate — Offset Square Marker
Pad Plate is a flat base plate with a small raised square pad near one end, built as a clean surface for labels, stickers, or a colour swap. The pad is sized to sit comfortably on the plate and stays low enough to print cleanly in a few layers. Dimensions Plate: 28.5 × 40 × 3 mm Pad: 11 × 11 mm, 0.7 mm thick Pad position: centred in X, 2 mm in from the Y- edge Print notes 0.7 mm pad suits a 0.2 mm layer height at roughly 3 to 4 layers. Print flat, no supports needed. Pad and plate are separate colour regions, so a filament swap at the pad layer works well.
Spider Web Plaque with GARTH Name
What it's for A flat spider web ornament with the name GARTH raised across its centre. Suitable for wall hanging, Halloween decor or a themed gift. Dimensions Web diameter: about 132 mm Thickness: 2 mm web, 4 mm with lettering 12 spokes, 4 concentric rings, hanging loop at top Lettering: 10 mm size, Permanent Marker font Remix ideas Swap the name or change the font Add a plush spider on a ring Scale down for a keychain or ornament
Balance Coffee Raised Letter Sign
A flat rectangular sign with raised "BALANCE COFFEE" lettering in Archivo Black, sized for a shelf, counter or wall. Remix hooks Plate size: 140 × 40 × 4 mm with a 1 mm chamfer. Widen it for a longer sign, or stack the two words on two lines and make the plate taller. Letter height: 2 mm raise, text size 11. Go to 1 mm for a quicker print, or 3 mm for stronger shadows. Colours: the plate and letters are separate regions. Print with a filament swap at layer 4 mm for a two-tone sign. Mounting: no holes yet. Add two screw holes near the ends, or a rear slot for hanging. Pairs with: a small stand or a wall bracket.
Ember Drake Charizard Mini Figure
A miniature Charizard collectible with a smooth rounded head, snout, small horns and green eyes, plus a cream belly that follows the curve of the torso. Two broad blue-green wings sit on the upper back, and a long tapering tail curves up to a red-and-yellow flame. Design notes Wings, arms and tail sit on captive ball joints with 0.35 mm clearance, so they can swivel after printing. Legs and feet are fixed to the body, which gives the figure a stable stance. Wing membranes are 2.4 mm thick with rounded edges. Colour regions: orange body, cream belly, teal wings, green eyes, red flame with a yellow core.
Extruder Figure on Cloud Plate
A printable extruder-style character lying on its back, standing in front of a solid 2 mm cloud plate. The name "Printytron" is raised on the body below the screen and is a separate part, so it can be coloured on its own. Boxy body with a recessed magenta screen showing a face with curved eyebrows and pupil indents Curved arms, thick hands, side box with teal button Hexagonal nozzle with a chunky square collar, flat on the plate Raised Space Mono lettering in its own colour Cloud backing plate whose bottom edge lines up with the hands and nozzle so the print can stand on a desk
16 mm Ball Track with Support Post
A 350 mm ball track (250 mm slope at 17.5° plus 100 mm flat) with a matching target ball support post for a 16 mm ball. Fit Track: 24 mm wide, 17.5 mm U-groove, 16 mm ball. Post: 24 mm base, 9 mm rod, 22 mm tall, flaring to a 20 mm head. Seat: 16.5 mm diameter, 3.5 mm deep spherical pit. Post axis sits so the ball-to-ball gap from the groove end is about 12.5 mm. Check before printing Measure your ball. The seat is sized for 16 mm and will not suit balls much larger or smaller. Known incompatibilities The post is a separate part that sits on the table. Its ball centre sits higher than the ball centre at the groove exit, so shim the track up or trim the post height to match.
Welcome — Cursive Neon Strip Holder
Welcome is a script-lettered sign form with an open channel running through every letter, built for pressing flexible LED neon strip into place. Fill the channel, wire it up, and the flowing lettering glows like a custom neon sign. Features Heavy brush-style "Welcome" lettering 1.6 mm walls around an open top channel 2 mm floor, 10 mm overall height Wire exit holes through the floor at the ends of the word Print notes Prints flat with no supports Strip width varies by brand, so check the channel width against your strip first
14 x 14 x 13 mm Palm Cavity Hand
A stylised hand with the middle finger extended and the other fingers folded, with a square 14 × 14 mm cavity, 13 mm deep, centred in the palm. Fit and check Cavity: 14 × 14 mm opening, 13 mm deep, open on the palm side, blind (does not exit the back of the hand). Palm is 22 mm thick, leaving about 9 mm of material behind the cavity floor. Measure the cavity after printing if a 14 mm part must fit; FDM usually shrinks holes slightly. Not included No reference image was available, so proportions are generic. Fingernail is a small raised plate on the back of the middle finger. It does not show from the palm side. Scaled compact, about 104 mm tall, so it is not life-size.
Pumpkin Phantom Witch Hat Figurine
A friendly ghost rising from a jack-o'-lantern, topped with a chunky witch hat. A 70 mm single-piece figurine with a flat base and no fragile tips. Remix hooks Hat height: the cone is two stacked segments (10 mm and 8 mm); stretch them for a taller hat. Brim: 36 mm wide, 3 mm thick. Widen it, but add support beyond about 40 mm. Face: carved triangle eyes and a rectangular mouth on the pumpkin; swap in a toothy grin. Ghost arms: simple 8 mm round nubs. Lengthen them into waving arms. Pairs with: a round display plinth, or a tealight-sized base for a lamp variant.
Printytron Extruder Figure, 85 mm Wide
Desk figure of the Printytron character, styled after an extruder. It prints lying on its back, so the whole underside sits flat on the plate and no supports are needed. The body has a recessed magenta screen with a face (eyes with pupil indents, curved eyebrows, smile), a teal button on a side box, curved arms ending in round hands, and a hexagonal tapered nozzle on a square collar. "Printy.dev" is engraved below the screen. Specs Overall size: about 85 mm wide, 76 mm long, 15.5 mm tall as printed Orientation: back face down, screen facing up Body thickness: 14 mm; arms 5 mm thick; hands 10 mm thick Side box: sloped underside (about 50° from the plate) so it prints without supports Antennae: run down to the back face, so they print flat Nozzle: hexagonal cone with a flat underside along its full length, on a 22 mm square collar with a 1 mm bottom chamfer Engraving: "Printy" at 8 mm and ".dev" at 4 mm, Space Mono, about 1 mm deep Colours: yellow body, magenta screen, teal button; suited to a multicolour print or painting after printing
Heart Plaque With Levy and Leny
A heart-shaped plaque with two raised names, "Levy" on the upper line and "Leny" directly below it. The names are raised so they can be read by sight and by touch, and nothing else is written on the piece. Print details Heart footprint: about 85 × 78 mm Total height: about 10.3 mm (9 mm stepped, domed body plus 1.3 mm of lettering standing proud) Lettering: raised, printed as one piece with the heart Print flat, base down, with no supports needed Two colours are possible with a filament change at the lettering layer
Need a part that doesn't exist yet?
Start building →