3D Model Gallery
Every one of these started as a sentence — real dimensions, real holes, print-ready STL. Remix any of them, or describe the part you need and Printy builds it. Start building →
Newest
5 Resin Bookmark Mold
An open-face silicone-free printed mold block with five rounded-end bookmark cavities side by side. Overall size is 175 × 145 × 6 mm, so it fits most print beds. Each cavity has fully semicircular ends, a shallow inner recess, and a small peg near the top that forms the tassel hole. Pour resin to the rim and level the mold while it cures. Overall size: 175 × 145 × 6 mm Five cavities, each about 30 × 137 mm Peg for a 5 mm tassel hole in every cavity Prints flat, no supports needed Apply mold release before casting
Modular Hexagonal Phone Stand
What it's for A single-piece modular phone stand designed around a regular hexagonal footprint. It features an angled 70-degree backrest for optimal viewing and a sturdy front retaining lip. A central U-groove is carved through the front lip and into the base, allowing a charging cable to pass cleanly underneath the phone while docked. The stand is designed to tile: dovetail tabs on the right side match with identical slots on the left side, allowing multiple hexagonal units to be linked together into a continuous charging array or desk organizer without any extra hardware. Dimensions Base size: 80 mm across opposite vertices, sitting 6 mm thick. Back panel: 65 mm tall, leaning back at a 20-degree angle from vertical. Front lip: 10 mm high above the resting surface, leaving a generous 23 mm gap for the device. Cable groove: 12 mm wide, recessing down to a 2 mm floor height. Print notes Designed to print entirely support-free in its default upright orientation. The 0.2 mm clearance on the dovetail joints should slide together firmly on a well-calibrated machine. Standard PLA or PETG will provide plenty of strength for the upright panels.
Modular Hexagonal Phone Stand
What it's for A single-piece modular phone stand designed around a regular hexagonal footprint. It features an angled 70-degree backrest for optimal viewing and a sturdy front retaining lip. A central U-groove is carved through the front lip and into the base, allowing a charging cable to pass cleanly underneath the phone while docked. The stand is designed to tile: dovetail tabs on the right side match with identical slots on the left side, allowing multiple hexagonal units to be linked together into a continuous charging array or desk organizer without any extra hardware. Dimensions Base size: 80 mm across opposite vertices, sitting 6 mm thick. Back panel: 65 mm tall, leaning back at a 20-degree angle from vertical. Front lip: 10 mm high above the resting surface, leaving a generous 23 mm gap for the device. Cable groove: 12 mm wide, recessing down to a 2 mm floor height. Print notes Designed to print entirely support-free in its default upright orientation. The 0.2 mm clearance on the dovetail joints should slide together firmly on a well-calibrated machine. Standard PLA or PETG will provide plenty of strength for the upright panels.
Holder
A rigid dash mount built to exactly fit an 80x160mm phone. Features a minimalist capture system: the phone slides in vertically and is retained by four small 11mm corner cuffs. The cuffs feature a deeply cut geometric star framed by a shallow 0.5mm engraved swirl. A rigid 2mm backstop spans the bottom cuffs to prevent the phone from slipping through. Footprint: 80x160mm exterior Retention: Four slim corner cuffs (top-loading) Mount: Standard 17mm ball joint (fits common dash and vent sockets) Detailing: Engraved swirls over star cutouts
Squarebody Pickup Frame and Shell
A slab-sided late-70s Ford pickup shell in the squarebody mould, paired with a 4x4 ladder frame. The body has a flat hood, upright windshield, boxy cab with a flat roof and a straight-sided bed, with square wheel openings at both axles and a slotted grille. Design notes Body prints separately and sits over the frame on four pinned mounts Underside is open so it drops over the rails Frame has arched rails, shock towers, battery cradle and electronics plate Pairs well with a two-tone paint job
Staggered 6-Mug Wall Rack
A heavy-duty wall rack designed to hold six mugs by their handles. The 280mm backplate staggers the layout into two distinct rows, ensuring wide ceramic rims have clearance and don't collide. Each peg tilts 12 degrees upward from the base to keep cups from sliding off under vibration. Remix Parameters Peg Dimensions: Built at 50mm long and 12mm thick for chunky handles. Shrink the diameter if you want to hang delicate teacups, or extend the length to stack espresso cups. Layout Grid: Peg centers are spaced roughly 90mm apart horizontally. The hull points can be compressed if you are short on wall space. Mounting Interface: Currently anchored by four 4.5mm countersunk screw holes. These can easily be swapped for slotted keyholes if the rack needs to be removable. Material & Strength: The pegs feature a 22mm flared base for leverage. If printing in a rigid, brittle filament like PLA, expanding that base diameter will add shear strength to the bottom row.
Phoen
A car phone holder built around a robust 12mm deep five-point star backplate. Fully rotating via a standard 17mm socket ball, this cradle features deeply pocketed bottom hooks and wraparound side arms designed to safely encapsulate heavy devices like an iPhone 15 Plus. Fitment: Wide 88mm interior span fits iPhone 15 Plus with standard cases. Mounting: Standard 17mm ball joint interfaces directly with generic dash and vent sockets. Restraint System: 4-point captivity (two lower shelves, two wraparound side grips) stops forward-tip during hard braking. Orientation: Rotates 360 degrees on the mount ball for landscape or portrait viewing.
Split-Span Laser Gantry
A modular laser mounting gantry spanning an exact 330mm width. Built for smaller print beds, the two-piece frame locks together in the centre with a clearance-tuned puzzle joint that draws the span tight when seated. Adjustments & Tolerances The Joint: 0.5mm clearance around the jigsaw neck. Best printed flat to put layer strength along the span. The Slider: Sits exactly over the seam and locks down with an M4 tap bolt through the top. Laser Mount: Single 6.5mm hole on the face block, ready for standard laser unit clamps. Table Mount: Four 5.5mm mounting holes positioned straight down through the feet for screwing straight into your baseboard.
Base Vela de Té 38mm (Baja)
Portavelas cilíndrico minimalista adaptado para mesitas de noche. Diseñado específicamente para recibir una vela de té estándar. Diámetro exterior: 66 mm (base estable) Altura total: 45 mm (perfil bajo) Asiento de vela: 39.5 mm de diámetro x 16 mm de profundidad, compatible con velas de té de 38 mm.
Twisted Planter With Name Plaque
A 100mm base hexagonal planter with a deep twist and a prominent front plaque. The planter features a solid 5mm-thick wall that precisely tracks the exterior twist, terminating in a flared rim. It includes a central 8mm drainage hole alongside five 10mm perimeter holes. A pill-shaped plaque sits seamlessly flush on the front face, equipped with extruded placeholder text ("NAME") that will export as part of the geometry—ideal for setting up multicolour text in your slicer. Check your drip tray to ensure the 100mm base clears the lip.
Anello Frazionato da Palo
Un anello di spessoramento diviso a metà, progettato per essere montato attorno a un palo da 137 mm di diametro. Profilo: Parete spessa 3 cm Fori: Quattro fori passanti verticali, diametro 4 mm, disposti in quadrato con lato 121 mm Assemblaggio: Spaccato centralmente per consentire l'installazione su tubi e pali esistenti senza doverli sfilare. Utile per creare spessori o basi su tubolari in metallo o PVC.
Piedino Subwoofer in TPU
Piedino antivibrazioni da 60 mm progettato per subwoofer, con geometrie ottimizzate per l'assorbimento acustico se stampato in TPU. Diametro: 60 mm Altezza: 25 mm Fissaggio: Foro centrale da 5 mm (ideale per viti da 4,5 mm) con svasatura, compatibile anche con montaggio a biadesivo Design: Scanalature concentriche sul fondo per aumentare la flessibilità del materiale e isolare le vibrazioni dal pavimento
Passat B6 Console Cup Holder 1.2v
A drop-in dual cup holder insert designed to fit the console space next to the handbrake in a 2006 Volkswagen Passat B6. The wedge-shaped body maintains a flush, horizontal top surface while following the sloped floor of the compartment underneath. Fitment: 180mm x 105mm footprint, tapering from 90mm down to 55mm in height. Capacity: Two 75mm diameter slots. The forward slot runs 75mm deep, and the rear slot sits 60mm deep to accommodate the console's slope. Features: Flared top lips for easy alignment, internal bottom fillets, and 5mm center drainage holes to handle condensation. Tolerances: Generous minimum wall and floor thicknesses (≥4mm throughout) ensure structural rigidity without requiring internal supports.
Cascading Hex Organizer
A minimalist, honeycomb-inspired desk organizer that steps up in height to hold everything from SD cards to tall pens. Its stepped layout is optimized for rapid support-free 3D printing. Zero Supports Required: Designed to print flat on the bed with no overhangs. V-Groove Details: Chamfered edges create a premium architectural look where the cells meet. Stepped Heights: Makes smaller items just as easy to grab as tall ones.
Screwdriver Handle With Bit Storage
Digging through a loose pile for the exact bit wastes time, so this 1/4-inch hex screwdriver handle keeps six spare bits loaded directly in the base. The main driving socket holds the active bit with a recessed magnet, while the spare slots are kept out of the way so the sharp ends stay clear of your grip while turning. Fit and Hardware Overall Size: 100 mm long by 30 mm diameter. Main Socket: 1/4-inch (6.35 mm) hex, sized to 6.6 mm for printed clearance, with a pocket at the bottom for a standard 6x3 mm neodymium magnet. Spare Magazine: Six hex slots cut 18 mm deep, leaving roughly 7 mm of a standard 1-inch bit exposed so they can be pulled out by hand. Grip: Six flutes offset from the bit holes to maintain wall thickness and provide torque.
Curved Script Chili Sign
A solid-backed, flat-printing chili pepper display sign styled like a vintage embroidered restaurant logo. The lettering is wrapped along a shallow crescent arc using a flowing, connected script font, layered with a dark stepped outline to give it a physical embroidered look. Everything sits flush on the Z=0 plane for easy multi-color filament swapping on any FDM printer. Remix Hooks The Curve Radius: The text is mapped along an arc with a 200 mm radius. Dropping that to 150 mm gives a much steeper smile, while pushing it to 300 mm flattens it out. Text Spacing: The script kerning is tied to a custom letter spacing offset. Adjusting this tightens or spreads the cursive connections. Outline Depth: The dark outline is offset by 1.5 mm. Bump that up for a thicker border.
Wide Stance Filament Spool Stand
Filament spools that hang off the edge of undersized holders are a constant source of drag and jams. This A-frame stand widens the track, catching oversized spools before they can derail. Fit and Bed Limits Inner Clearance: 160 mm between the uprights Base Width: 180 mm Spindle Height: 192 mm Printability: The entire layout is spaced to fit on a 220x220 mm bed without needing rotation or supports.
Emulation Station
A barebones active cooling enclosure designed to swallow a standard 120mm PC fan and keep a board chilled. The built-in snap-fit pegs mean you don't need hardware to mount the fan—just press it into the ceiling and let the flexible split cones lock over the flanges. Remix Hooks Dimensions: Currently set to 150mm inside, keeping 3.2mm walls. Ports: USB-C and HDMI cutouts sit on the left wall, maintaining a 15mm offset from the front corner to line up with a standard single-board computer. Power: A 19mm switch hole is punched straight into the back wall, sitting 20mm off the base. Next Steps: Plenty of room inside for custom standoffs, sleds, or cable management brackets depending on what board you're mounting inside.
projected displayit
A heavy, grounded display pedestal featuring an oversized, tapered rectangular frame. Designed to house a graded trading card or slab, it features a built-in cavity underneath for a 72mm LED puck light. The uplight casts through the vented base to illuminate the card inside the pass-through tunnel. Remix Hooks Base footprint: The base extends well beyond the frame to give it a solid stance — currently 200x120mm on the bottom tier. Frame pitch: The upper frame tapers deeply front-to-back while maintaining a steady 150mm width, giving the whole piece a commanding silhouette. Text & Shadow Carvings: The "DISPLAYIT" front text (size 8 Marcellus) and the abstract, smoke-like internal wall carvings are perfect candidates to tweak depending on what theme your display needs.
160mm Square Base Plate
What it's for A simple, flat 160mm square plate, suitable as a foundational base, shim, or blank canvas for further structural modifications. Dimensions Width & Length: 160 mm x 160 mm Thickness: 4 mm Remix ideas Subtract precise mounting holes to use it as an electronics sled. Carve out a hex grid to create a lightweight mesh panel. Emboss or deboss a logo into the top face.
Magnetic Enclosure Storage Box
A robust two-piece enclosure designed around magnetic closures and standard 100x145x30mm internal storage requirements. Remix Hooks Wall Thickness: Set to 6mm to ensure the 4mm corner magnets have plenty of structural meat on both sides. Registration Lip: The lid features an inset lip with 0.3mm clearance to keep the halves aligned—the magnets just pull it shut, they don't have to fight shear forces. Bottom Magnets: 7mm diameter cutouts are positioned underneath for docking or stacking. Adjust their X/Y offsets if you're matching a specific grid plate.
Moderne Zweifarb-Pflanzenschilder
Diese drei Pflanzenschilder kombinieren ein sauberes, zweifarbiges Layout mit einer robusten Konstruktion. Der Grundkörper misst 160 mm in der Gesamtlänge, wobei ein verstärkter Erdspieß für sicheren Halt im Substrat sorgt. Der doppelte Rahmen und die moderne serifenlose Schrift heben die Beschriftung ("White Widow" und "The Church") deutlich hervor. Design- und Druckhinweise Zweifarbdruck: Konzipiert für einen Filamentwechsel ab Z-Höhe 2,0 mm. Der Grundkörper bildet das Bett, während Ränder und Text als 0,8 mm starke Akzente aufsitzen. Verstärkung: Eine konisch zulaufende Mittelrippe auf dem Erdspieß verhindert ein Abknicken in dichter Erde, ohne den Druck zu verkomplizieren. Keine Stützen nötig: Die Schilder liegen komplett flach auf dem Druckbett und können direkt nacheinander oder gleichzeitig gedruckt werden.
Small Faceted Planter
A compact, faceted geometric planter pot designed for small succulents and cacti. The intersecting octagonal shell forms a sharp, modern crystal profile. Dimensions: 60 mm height, ideal for shallow-rooted desk plants. Drainage: 5 integrated base ports (one center, four radial) to prevent root rot. Structure: 3 mm solid wall thickness.
Robot Mech
Action figures with spindly joints and complex overhangs are miserable to print on an FDM machine — they snap at the ankles or turn into spaghetti under the arms. This is a heavy, blocky mech suit designed entirely out of chamfered armor plates. It trades sculpted organic details for a robust, aggressive hard-surface geometry that actually prints. The figure stands in a strict A-pose with wide, flat feet to maximize bed adhesion. Print Parameters Total Height: 157 mm Footprint: 48 mm wide stance Supports: Required under the arms and crotch (the A-pose keeps them minimal) Joints: Solid model (no moving parts to fuse)
Need a part that doesn't exist yet?
Start building →