3D-printable kitchen & bathroom accessories
Dispensers, holders, covers and stands sized for everyday items. Browse what makers built, or describe the exact accessory you need and Printy makes it.
Need one that fits your exact measurements? Start building →
Newest
Cutting Board Corner Grip Feet
A set of four corner cups that slip over the corners of a cutting board and grip the counter, so the board stays put under a knife. Each foot is a 25 mm square cup, 8 mm tall, with a corner socket on top and a gently domed, nubbed underside. The socket has 2.4 mm walls on the two outer sides and a 2.5 mm floor, so it is 5.5 mm deep. The two inboard sides are open, so the board corner slides in and the outer walls hold it. The underside rises about 1.2 mm toward the centre and carries 1 mm grip nubs on a 2 mm pitch. Remix hooks Socket depth: the floor is 2.5 mm, which leaves 5.5 mm of grip. Thinner floor or taller cup means a deeper hold. Heavy or thick boards benefit most. Cup footprint: 25 mm is a choice, not a constraint. Go larger for more adhesive area or a wider stance. Wall thickness: 2.4 mm on the outer sides. Raise it for a stiffer clamp, lower it toward 1.6 mm for more flex. Nub size and pitch: 1 mm nubs at 2 mm spacing. Larger, sparser nubs give more bite on rough counters. Finer ones suit smooth laminate. Dome rise: 1.2 mm. Set it to 0 for a flat base with the same texture. Closed-corner variant: add walls on the inboard sides for a full pocket, with a slightly oversize opening for easy loading. Notes for printing and pairing TPU is the sensible material, since PLA nubs will not grip much. A dab of adhesive in the socket helps on heavy boards. Pairs with non-slip shelf liner or rubber pads under the cup as a second grip layer. The 4 feet are laid out in a 2 by 2 grid with 6 mm gaps.
Bifold — Magnetic Folding Hex Drying Tray
Bifold is a two-panel folding drying tray, 230 mm square when open, with a dense honeycomb of hex holes for draining. A captured-pin hinge joins the panels, and magnets hold the tray closed for travel. Five magnetic legs store in a long groove along the outer edge. The magnet pockets sit directly in the honeycomb lattice, in place of individual hex cells. That removes the solid patches that used to surround each pocket, so the tray stays as open as possible. Features 5 mm panels, 230 mm overall Print-in-place captured-pin hinge Hex holes about 10 mm across the flats, 2 mm ribs 8.2 mm × 2.75 mm magnet pockets, set into hex cells 7.4 mm wide, 3.6 mm deep, 156 mm long leg grooves In the box Five 7 mm legs with 6.2 mm × 2.8 mm magnet holes in both ends Print notes Print flat with the hinge side up. Legs print best in PETG with extra walls. Print a short hinge test first, since clearances are tight.
Softflow — M22 Faucet Splash Diffuser
Softflow is a screw-on splash diffuser for faucets with an M22x1 male outlet thread. The base is perforated with a staggered hex grid of small holes, breaking the flow into many fine streams for a softer, wider spray. A short open chamber between the thread and the perforated floor lets water spread across the whole hole pattern before it exits. Features M22x1 female thread, 8 mm deep, with a beveled lead-in at the opening Staggered hex grid of 1.5 mm holes at 2.6 mm spacing, inside an 18 mm circle 3 mm perforated floor with a relief chamber above it Chamfered top and bottom edges on a round body Dimensions Outer diameter: 28 mm Overall height: 16 mm Thread: M22 x 1 mm pitch, 8 mm engagement depth Floor thickness: 3 mm Print notes Print with the perforated face down on the bed, opening facing up; no supports are needed. Thread fit has not been tested against a real faucet. If it binds, increase the thread clearance slightly. A fine layer height (0.12–0.16 mm) keeps the small holes and thread crisp. PETG or ASA suits wet, warm-water use better than PLA.
Square-Base Bowl That Stays Put
A bowl that skids across the counter or tips the moment you stir it is the annoyance; this one has an almost square base that keeps it planted. The base is a 70 mm square with rounded corners, so it sits flat instead of rocking, and the walls flare out to a 120 mm rim that is rounder and easier to eat from. What decides the fit Base footprint: 70 mm rounded square — the number to check against your shelf, tray or cupboard. Rim: 120 mm across at the widest point. Height: 50.8 mm (2 in). Walls and floor: 3 mm thick, so it holds its shape without being heavy. It prints as one piece, standing on its flat base, so no supports are needed and the inside comes out clean.
Bag Holder Stand with Spring Clamp Ring
A freestanding stand that holds a freezer or piping bag open so both hands are free for filling. The bag mouth is pulled through a 120 mm inside-diameter ring, folded over the outside, and secured with a separate split clip that grips the folded rim all the way round. The base is a wide 270 × 250 mm plate with a rear post, so the stand resists tipping when a bag is loaded. The ring sits at the top of the post, 165 mm above the plate, with a flared lip to keep the fold from slipping off. Ring: 120 mm inside diameter, 40 mm tall, on a short arm off the post Base: 270 × 250 mm, 8 mm thick, chamfered edges, with a gusset on the post Clip: split spring ring, 24 mm tall, with finger tabs for opening Parts: base with post, ring, and clip are colour-labelled; the clip prints separately Material: PETG suggested for the clip so it keeps its spring To use, pull the bag mouth up through the ring, fold it down over the outside, then snap the clip over the fold. The ring height suits bags up to roughly 165 mm long; longer bags will rest on the base. The clip's grip has not been test-printed, so the gap may need adjusting for thicker or thinner bag film.
Leanto — Sawtooth Taco Rack
Leanto is a minimal plate-top rack that holds three hard taco shells upright at a 45° slant, one behind the other. The profile is a true sawtooth: each slanted surface ends in a vertical wall that also stops the next shell, with no solid base underneath. Features Three 45° ramps, 48 mm pitch, 48 mm tall vertical backs Open underside, 3 mm shell walls One forward-leaning stop at the front to hold the first shell Two thin side runners tie the teeth together Dimensions About 100 mm wide and 150 mm front to back Fits on a standard dinner plate
Square Bioplastic Tile Mold with Corner Pins
What it's for A square casting mold for thin, translucent starch-based bioplastic tiles. Four pins inside the cavity leave a hole in each corner of the cast tile, so neighbouring tiles can be tied together with fishing line into a stained-glass-style hanging grid. Dimensions Cavity: 120 × 120 mm, 2 mm radius inside corners Outer size: 124 × 124 mm, total height 6.2 mm Walls: 2 mm thick, 5 mm above the floor Floor: 1.2 mm, continuous and flat underneath Pins: 4 mm diameter, 4 mm tall above the floor, centred 8 mm from both adjacent inner walls, clear of the walls Print notes One solid piece, no supports, flat underside Pins are fused into the floor Low filament use thanks to the thin floor and walls Remix ideas Change the pin spacing for larger or smaller holes Add mid-edge pins for extra connection points Scale the cavity for rectangular or smaller tiles
Open Square Casting Mold Frame
A flat, bottomless square frame for casting starch bioplastic sheets on a silicone baking mat. Outer size is 124 × 124 mm with a 120 × 120 mm opening, 5 mm tall, 2 mm walls and 2 mm corner radii. Remix hooks Opening size (120 mm): change it for other sheet sizes; the outer size is the opening plus twice the wall. Height (5 mm): sets the casting thickness. Raise it for thicker sheets. Wall (2 mm): 3–4 mm gives a stiffer frame that resists warping. Pairs with: a silicone mat, or a clip-on cross brace or divider to cast several smaller tiles. Lower edges are flat, so it prints with no supports.
Toy Story Sky Cloud Cookie Cutter
A cookie cutter echoing the wallpaper clouds from Andy's room: a big bump on the upper left, smaller puffs along the top and a long flat base. The centre is open so dough passes straight through. 15 mm tall wall, about 1.2 mm thick, thin clean cutting edge on the flat bottom Widened rim at the top for pressing by hand About 100 mm wide, prints flat with no supports
Three-Slot Curved Taco Stand
A taco stand that holds three shells upright and open-side up, so fillings stay in place while you load them. The base is a flat 180 × 120 mm block with rounded corners. Three curved slots are cut into it, each one cradling a single shell. Four round feet lift the base off the table. Each slot arcs along its length, which follows the curve of a folded shell. Three curved slots, each 90 mm long and 20 mm wide Slots spaced 55 mm apart across the 180 mm base Base 22 mm thick, with the slot floor 6 mm above the underside of the block Four round feet, 5 mm tall, with chamfered edges Rounded vertical corners on the base Prints flat on its feet, with no supports needed If your shells are wider than 20 mm, widen the slots before printing. Food-safe filament such as PETG is a sensible choice, and a wipe-down after use keeps it clean.
Caneca Stein 110 mm para Copo Ø96
Caneca estilo stein tricolor (branco, vermelho, preto) com cavidade cilíndrica Ø96 mm para copo de alumínio removível, acompanhada de luvas de redução e elevadores de fundo. O que encaixa Cavidade Ø96 mm, profundidade útil 165 mm; rebaixo Ø105 mm no anel superior para o flange da luva. Luvas A (88–93), B (82–87), C (76–81) e D (70–75 mm), com cone de cerca de 2,3°, 8 nervuras de 0,45 mm e dois entalhes de dedo. Elevadores de fundo de 5, 10 e 20 mm com furo central e canal de respiro de 3 mm. Medida a conferir antes de imprimir Diâmetro externo do lábio e do corpo do copo real. A luva A tem parede de apenas cerca de 0,9 mm no topo; meça o copo antes de fechar as faixas. Não inclui Textura de malha, dobras de tecido, baioneta do anel e as três estrelas. Qualquer outro diâmetro de cavidade sem alterar os parâmetros. Altura total 195 mm, Ø externo 110 mm, projeção da alça cerca de 47 mm. Parede dupla de 3 mm de ar com nervuras a cada 30°, base com 8 bolsões para arruelas e tampa removível.
Mango recto con soporte giratorio
Mango recto con soporte giratorio para cuchara, de 12 cm de largo total, 2,8 cm de ancho y 1,6 cm de alto. Se compone de dos piezas independientes unidas por un tornillo M4 vertical y una tuerca hexagonal en la parte inferior. El soporte abraza una lengüeta circular del mango y pivota alrededor del tornillo, de modo que la cuchara se orienta a derecha o izquierda y se fija al apretar. Largo total: 12 cm Mango: unos 9,4 cm, se afina hacia el extremo Lengüeta de 4 mm con disco de 20 mm y orificio de 4,6 mm Soporte con ranura de 4,4 mm y alojamiento para cabeza de tornillo y tuerca M4 Tornillo y tuerca no incluidos
Mango curvo con soporte de cuchara giratorio
Conjunto de dos piezas independientes: un mango curvo de 120 mm y un soporte de cuchara que se encaja sobre su extremo. La unión se hace con un tornillo M4 vertical, introducido desde arriba, y una tuerca en la parte inferior. El soporte abraza una lengüeta circular del mango y pivota alrededor del tornillo, de modo que la cuchara se orienta a derecha o izquierda y se fija al apretar. Especificaciones Mango: 120 mm de largo, 25 mm en la base, 20 mm en el extremo, 16 mm de grosor. Lengüeta del mango: 4 mm de grosor, disco de 20 mm, orificio de 4,6 mm. Soporte: ranura de 4,4 mm, orificio pasante de 4,6 mm. Cabeza del tornillo alojada arriba; tuerca M4 hexagonal alojada abajo. Alojamiento de la cuchara: 14 × 5 mm. Tornillo y tuerca M4 no incluidos.
Cucharilla de dos piezas con conector
What it's for Mango curvo tipo banana y conector independiente con dos pestañas flexibles. El conector encaja con un clic en el alojamiento del mango y se retira pellizcando las pestañas a través de las ventanas laterales, sin herramientas. Dimensions Mango: 120 mm de largo, 25 mm de ancho en la base y 20 mm en la punta, 16 mm de grosor. Alojamiento: 16 × 6 mm, 23 mm de profundidad. Conector: núcleo de 22 mm, 5,6 mm de grosor, brazos de 1,6 mm con resalte de clic. Ventanas laterales de 4 mm donde se aloja el resalte. Remix ideas Añadir una cabeza de cuchara en la pestaña tope del conector. Ajustar el grosor de los brazos (1,6 mm) para un clic más suave o más firme. Cambiar el radio de curvatura del mango.
Smart tap attachment
Assembled touchless tap attachment: a 110 × 80 × 60 mm ABS enclosure with every internal component mounted in place, plus a specification plaque in front. What it mates with Tap adapter for 15–24 mm taps, with a 20 mm ID / 28 mm OD / 3 mm silicone O-ring beneath it 6 mm OD / 4 mm ID PU tubing to 1/4" (6 mm) quick-connect fittings and a 12 V NC solenoid valve E18-D80NK IR sensor through an 18.5 mm bore in the front wall Inside the enclosure 50 × 40 mm control PCB and 35 × 25 mm SPET driver on standoffs with M3 screws 35 × 25 mm relay module and a 12 V power supply block Red wiring harness between boards, sensor, solenoid and power supply Floor tube clip and four lid screw bosses (M3 × 10 mm) Check before printing The lid sits beside the enclosure so the interior stays visible. The power supply is a 30 × 40 × 22 mm representative block, since no size was specified, so check it against your actual unit. The sensor bore suits an 18 mm body only. Other enclosure sizes are not covered.
Antalya Kebap Untersetzer 3.0
Runder Getränkeuntersetzer im Kebap-Stand-Look: Die Schrift ANTALYA KEBAP II steht 1 mm erhaben auf einer glatten Fläche, umgeben von einem hohen Rand, der Kondenswasser und Verschüttetes im Zaum hält. Durchmesser 100 mm, Boden 5 mm stark Umlaufender Rand bis 6 mm Höhe Schrift 1 mm erhaben, Bebas Neue Die Schrift endet auf Randhöhe, daher bleibt oben alles bündig
Obsidian — Ribbed Can Cooler with Handle
Obsidian is a matte-black-ready can cooler for standard 330 ml cans, with a reinforced side handle, diagonal grip ribs and a flat front panel reserved for names or logos. The handle opening has a peaked top so it prints upright without supports. Dimensions Inside diameter: 68 mm Inside height: 105 mm (above a 3 mm base) Wall: 2 mm, base: 3 mm Overall height: 108 mm; footprint about 115 × 74 mm including handle and panel Features Diagonal ribs outside, perfectly smooth bore inside Rounded top rim Broad, rounded handle, 24 mm wide Flat front panel, 40 × 66 mm Print notes Print upright, base on the plate, PETG, 0.4 mm nozzle, 0.2 mm layers No supports expected; fits a 180 mm build volume
Round Water Bottle With Cap
A round water bottle with a tapered shoulder, a 24 mm mouth and a separate slip-on cap. Printed as a hollow vessel with 3 mm walls. Remix hooks Body diameter and height: 70 mm wide, 170 mm straight section. Change these to resize capacity. Wall thickness: 3 mm. Raise it for watertight prints in PLA, or lower it with vase mode in mind. Neck: 24 mm bore, 30 mm outside. Swap the plain cap for a threaded one using a threaded rod and nut. Pairs with: a silicone gasket, a carry loop through the neck ring, or a sleeve that fits the 70 mm body. The cap is a friction fit and not a sealed closure. Test before filling.
HexCatch — Geometric Coaster
Introducing HexCatch, a 90mm circular coaster engineered to keep surfaces perfectly dry. The surface features a recessed, concentric hexagon pattern that acts as a condensation trap, drawing moisture away from the base of glassware before it can pool and run onto the table. \n\n## Dimensions\n Overall footprint: 90mm diameter\n Thickness: 5mm \n Channels: 2mm wide and 1mm deep\n\n## Features\n Integrated drip reservoir: Geometric recesses hold condensation safely off the table.\n Modern profile: A clean circular exterior contrasts with the sharp hexagonal interior.\n Chamfered base: Slight angle on the bottom edge makes it easy to lift from flat surfaces.
8.5 Inch Tall Round Steamer Basket with Lid
A round steamer basket, 216 mm (8.5 in) in outer diameter and 70 mm tall, with a separate conical lid. The floor is slotted for steam flow, and raised bands on the wall suggest bamboo. Basket: 216 mm OD, 70 mm tall, 5 mm floor, 5 mm wall Floor: radial steam slots in three rings Lid: conical, with a round knob, fits over the rim Bands: three raised rings, surface detail only Print: two separate pieces, lid printed flat side down
lid 2
A round plug-style lid for a container with a roughly 94 mm inside diameter. A 100 mm flange rests on the rim and an 8 mm deep, 93.4 mm plug drops into the bore. Fitment Fits: round containers with a bore near 94 mm. Does not fit: bores under 93.4 mm, or slip-over use on a rim. Measure before printing: the container's inside diameter. The plug is 93.4 mm, so a 94 mm bore leaves 0.3 mm per side. Details: the underside is hollowed to 87 mm, leaving a 3 mm flange top and a 3.2 mm plug wall. Overall height: 11 mm.
Weihnachtliche 3-Etagen Etagere
3-Etagen Steck-Etagere im weihnachtlichen Stil. Konzipiert für den separaten Druck. Teller: 160 mm, 120 mm und 80 mm Durchmesser, jeweils mit erhöhtem Rand (2,5 mm tief) und dezentem Rillenprofil (1,5 mm Profiltiefe). Säulen: 80 mm hoch, mit integrierten Zierkugeln im Abstand. Stecksystem: 11,5 mm Zapfen auf 12,0 mm Loch für spielfreie Montage. Topper: 5-zackiger Stern als Abschlussstecker.
55mm Recessed Text Cookie Stamp
A one-piece 55mm circular stamp designed to emboss raised text into cookie dough. Built for a school fair baking project, the face features 3mm deep recessed lettering, mirrored to read correctly on the final baked good. A domed palm-knob provides even pressure distribution during batch stamping. Dimensions: 55mm diameter face, 39mm overall height. Impression Depth: 3mm recessed text for crisp relief. Typography: Alfa Slab One, optimized for legibility in heavy doughs. Form: Domed top handle for palm-pressed leverage.
GlideTrak — Under-Shelf Stemware Rack
GlideTrak is an under-shelf stemware storage block designed to securely hold up to four standard wine glasses upside down by their stems. The dual-channel architecture features a continuous track that flares wide at the opening, allowing smooth, one-handed retrieval and stowing of glasses without requiring precise visual alignment. Engineered as a robust mounting block, it secures flush against the underside of a cabinet while maintaining a clean profile. Features Flared Entry: The stem slot narrows from a 14 mm flared opening down to a 9 mm continuous track, guiding standard stems seamlessly into place. Concealed Mounting: Six countersunk holes with screwdriver access tunnels provide secure upward mounting, hiding the screw heads deep within the block. Support-Free Printing: Engineered to be printed standing vertically on its flat back wall, allowing the internal cavities to form cleanly without the need for support material. Dimensions Overall Footprint: 212 mm wide × 170 mm deep × 22 mm thick. Base Clearance: 82 mm wide internal cavity per channel to accommodate standard glass bases. Stem Track: 9 mm track width, expanding to a 14 mm flare at the front entry.
Need a part that doesn't exist yet?
Start building →