3D-printable storage & organizers
Boxes, wallets, dispensers, holders and carriers sized for real contents. Browse what makers built, or describe the exact organizer you need and Printy makes it.
Need one that fits your exact measurements? Start building →
Newest
Open-Front Can Carrier1
Standard 355ml cans pile up in the fridge and roll around when you try to stack them. This is an open-front upright shelf carrier that holds six cans — three wide, two high — securely in their own cradles. The handle mounts at the top front and swings entirely clear of the loading area. When dropped back, the grip sits perfectly flush with the back wall of the crate, staying completely out of your way until it's time to lift it. Fit Details Capacity: 6x Standard 355ml cans (66.5mm diameter) Clearance: Cans slide in vertically from the open front Assembly: The handle prints flat. Just flex the arms outward slightly to snap the 9.5mm pegs into the crate's pivot holes.
150mm Borg Friendship Vault
Zak's Borg Friendship Vault. Three-piece print, designed to drop in and seat clean without fasteners. Overall Footprint: 150mm x 150mm. Total Height (Assembled): 145mm. Internal Payload Bore: 65mm diameter x 105mm depth. Cage Windows: 90mm span, designed to bridge flat across the top without support on well-calibrated machines. The top cap runs a 118mm square boss to locate itself on the outer frame, plus a 64.5mm cylindrical plug to lock into the core and prevent horizontal slop. Print the outer cage and cap in black PETG; run the core in fluorescent PLA. Keep your cooling aggressive for the long window bridges.
Garden Hose and Nozzle Hanger
What it's for A wall-mounted storage bracket designed to hold a standard 15-meter garden hose outdoors. It features a wide saddle for the main coil and an integrated upper bracket with a U-slot to suspend a spray nozzle securely, keeping it off the ground and out of the dirt. Dimensions Main Hanger: 200mm wide, extending 120mm from the wall to support bulky hose coils. Overall Height: 260mm tall backplate. Mounting: Three vertically aligned countersunk holes (12mm head clearance, 6.5mm shaft). Nozzle Slot: 28mm wide U-shaped cutout positioned 70mm above the main hanger. Remix ideas Modify the nozzle slot diameter to fit specific quick-connect fittings or larger spray guns. Adjust the mounting hole spacing to align with specific mortar joints or siding panels. Extend the main shelf depth and retaining lip height to accommodate a 30-meter hose.
Apache 2800 DS18 Speaker Ring
Adapts the factory grid structure of an Apache 2800 equipment case lid to accept a standard DS18 8-inch audio driver. Host Mating Surface: Drops directly over the factory 2800 grid ribs via 6.5mm deep rear clearance channels. Do not use if you have already shaved the case lid. Driver Fitment: Features a standard 182mm inner basket bore and a 197mm bolt circle. Standoff: Provides 12mm of total lift off the lid plane. Ensure your driver depth clears the case base when closed.
Under-Mattress Bedside Tray Caddy
Built for bedrooms with zero floor space for a nightstand. This caddy slides a 180mm paddle directly under the mattress, dropping a functional 180x120mm tray over the side of the bed frame. It features a recessed 70mm ring with a raised lip to secure a glass of water, plus a dedicated rear slot angled at 12 degrees to keep a phone visible and upright. Remix Parameters Riser Drop: The vertical riser is currently 60mm. Extend this dimension if a specific bed frame has exceptionally tall side rails that the tray needs to clear. Paddle Length: At 180mm, the under-mattress flap provides baseline leverage. Stretch it to 250mm or widen the base for heavier loads or thicker, softer mattresses. Surface Layout: The tray is an open 180x120mm canvas. The 70mm drink ring and phone slot can be mirrored for opposite-side beds, or swapped out entirely for modular charging pucks and glasses trays.
Standard 140x40 Gehäuse
Gehäuseunterteil mit Außenmaßen 140 x 40 x 25 mm und 3 mm Wandstärke. Passung: Der Deckel hat eine Innenlippe mit 0,5 mm Gesamtspielraum (0,25 mm pro Seite). Druck: Beide Teile liegen flach auf dem Druckbett (Deckel liegt auf der Oberseite) und benötigen keine Stützstrukturen. Kapazität: Innenraum misst effektiv 134 x 34 x 22 mm.
Barra 25mm Separador Tallas
Separadores de tallas diseñados para barras de ropa. Cuentan con un orificio de 25 mm exactos y una abertura lateral de 15 mm que permite introducirlos a presión sin tener que desmontar la barra ni retirar las perchas. Punto de anclaje: Barra de 25 mm de diámetro. Abertura: 15 mm (requiere ligera flexión al colocar si el material es muy rígido). Grosor: 5 mm. Comprueba el diámetro exacto de la barra del perchero antes de imprimir; las barras comerciales pueden variar entre 22 mm y 28 mm.
Barra 25mm Separador Tallas
Separadores de tallas diseñados para barras de ropa. Cuentan con un orificio de 25 mm exactos y una abertura lateral de 15 mm que permite introducirlos a presión sin tener que desmontar la barra ni retirar las perchas. Punto de anclaje: Barra de 25 mm de diámetro. Abertura: 15 mm (requiere ligera flexión al colocar si el material es muy rígido). Grosor: 5 mm. Comprueba el diámetro exacto de la barra del perchero antes de imprimir; las barras comerciales pueden variar entre 22 mm y 28 mm.
Ühe Otsaga Suletud Sahtlikarp
Sahtel kiilub kinni, sest pole kuskilt korralikult kinni võtta. See on suletud tagaseinaga lihtne kest, millel on nüüd sahtli ees korralik väike näpu-kõrgendus, et seda saaks mugavalt ja ilma küüsi murdmata välja tõmmata. Mahutavus: Täpselt 200 × 50 × 50 mm kasulikku ruumi. Seinad: 1.5 mm, prinditav ilma tugedeta. Liikumisruum: 0.5 mm lõtk külgedel tagab sujuva liugumise.
Filmdosen-Schuh 36mm
Ein flacher, passgenauer TPU-Untersetzer (Schuh), der das Wackeln einer hohen 36-mm-Filmdose verhindert. Innendurchmesser: 36,2 mm (für strammen Sitz in flexiblem Material) Gesamthöhe: 5,0 mm Bodenstärke: 1,6 mm Wandstärke: 1,65 mm Besonderheiten: Leicht abgerundete Außenkanten und eine 0,5 mm Fase an der Innenkante zum leichteren Einsetzen der Dose.
Penny Sleeve Display Stand
A dedicated three-slot display base dimensioned specifically for standard trading cards in penny sleeves (or top-loaders). The base spans 250 mm wide, offering three independent 70 mm x 5 mm straight grooves. The generous 5 mm slot depth easily clears a standard sleeve, and the solid 12 mm floor ensures they sit securely without sliding out of bounds. Groove Size: 70 mm wide x 5 mm deep x 12 mm tall Backing Plate: 110 mm tall Multi-Colour: Includes an embedded turquoise TCC logo separated as its own printable region.
Low-Profile Reeded Catchall Tray
A wide, low-profile oval catchall tray featuring a seamless ribbed exterior and a smooth inner basin. Dimensions: 200mm × 100mm × 22mm Wall Thickness: 5mm (with 5mm continuous exterior ribs) Floor Thickness: 5mm Use Case: Keys, loose hardware, or desk accessories. The shallow walls make it easy to reach in and grab small items.
VoltGrid — Print-in-Place Battery Case
A high-capacity, print-in-place storage case holding 104 AA batteries in a skeletal, material-saving grid. Designed specifically for FDM printing without supports. Features Zero Assembly: Prints flat with a fully integrated, captive 45-degree cone hinge mechanism. Just pop it off the bed and fold it closed. Skeletal Organizer: The lower grid provides 0.4 mm of clearance for 14.5 mm diameter AA batteries, but uses open walls to drastically cut filament usage and print time compared to solid block designs. Snap Latch: A flexible cantilever tab locks the lid securely down over a heavy chamfered ledge on the bottom box. Dimensions Flat Printing Footprint: 228 mm × 292 mm Closed Dimensions: 228 mm (W) × 142 mm (D) × 60 mm (H) Capacity: 104 cells (13 × 8 grid)
Side-Pinned 40-Quarter Dispenser
A gravity-fed mechanical magazine for standard U.S. quarters. The vertical tube stores up to 36 coins, while a sliding escapement mechanism stages and drops exactly four quarters ($1) per full pull. Design and Fitment Capacity: 40 quarters maximum (36 in the tube, 4 seated in the slider). Clearances: The magazine bore is 25.2 mm (oversized from the 24.26 mm quarter) to prevent binding, with a 28.8 mm x 7.6 mm slider track for horizontal travel. Structural Details: The base of the primary magazine tube features a 4 mm flared buttress, preventing shear failure across the layer lines when fully loaded. Hardware: Fully printed, no external fasteners or springs required. The side-mounted 4.0 mm stopper pin captures the slider in the track and sets the 26 mm travel limit.
104-Cell AA Battery Vault
This heavy-duty grid vault keeps 104 AA cells locked down and separated. The front closure uses a single wide flex-arm cantilever built straight into the lid. It swings down to snap automatically over a retaining ledge on the base, holding the lid firmly shut until you pull the finger grip outward. Clearance: 0.4 mm gap on all latch and hinge mechanisms Lid Mechanism: Print-in-place folded hinge Print Layout: Prints fully open and flat on the bed
Monolithic Table Tennis Rack
A monolithic, fully-bracketed table tennis storage unit designed to hold four adult-sized rackets in a parade formation. Secure Carriage: Drops rackets vertically into precision-cut 34mm pockets that capture both the handle and blade, eliminating forward/backward tipping. Support-Free: Profiles are fully optimized for standard FDM printing logic; it prints vertically as a single solid piece without bridging or internal scaffolding. Tethered Alignment: A heavy floor-plate combined with structural side rails ensures extreme rigidity against sideways deflection.
AutoBrush Head Travel Case
A protective travel shell explicitly shaped to match the AutoBrush U-shaped head without excess bulk. There's nothing more frustrating than opening your travel bag to find your toothbrush head snagged on something and exposed to the bottom of your wash bag. This clamshell encloses the head securely with mechanical latches tucked firmly into the straight side edges so they don't catch on anything. Fit & Print Details Hinge: Integrates a full-length structural hinge pin printed separately for maximum mechanical strength. Latch Mechanics: Dual snap latches cross the mating seam, biting tightly to keep the case closed when dropped. Support Requirement: Flat base layout means this case prints reliably with no supports and zero overhang spaghetti.
Bento-Style Parts Tray
A clean, symmetrical storage tray evoking the balanced proportions of a bento box. It splits the footprint evenly into two generous bays, keeping tools and components strictly separated but immediately accessible. Design Notes Built with stout 3 mm walls for shop-floor durability. Swept interior corners mean small parts slide out smoothly instead of getting trapped in the seams. Designed with a perfectly flat base and zero overhangs for a seamless print.
ArcGuard — Curved Locking Cage
Eine maßgefertigte, zweiteilige Sicherheits-Käfigstruktur mit einem massiven Basisring und einer gebogenen Gitterabdeckung. Der Käfig ist so konstruiert, dass er bündig auf dem Ring aufsitzt. Das integrierte Schließsystem wurde nach außen verlegt, um die Handhabung mit einem kleinen Vorhängeschloss zu erleichtern, während das Hauptrohr geschützt bleibt. Features Biegung: Die Käfigstruktur biegt sich um 25 Grad nach unten und vom Schloss weg, was den Platzbedarf in Schließrichtung minimiert. Ergonomie: Sämtliche Kanten, auch im inneren Gitterbereich und an der 10-mm-Abschlussöffnung, sind vollständig abgerundet – das Design kommt ohne harte Schnittkanten aus. Stabilität: Massive Stangenführung und 4 mm starke Gitterwände sorgen für hohe strukturelle Belastbarkeit. Print notes Beide Teile können flach nebeneinander auf dem Druckbett positioniert werden. Für die Gitterstruktur des Käfigs ist bedingt durch die Wölbung Support-Material erforderlich.
TipVault — Scaled Coin Box
A sturdy tip box designed to print in one piece with no supports or assembly required. It features a fully articulated, print-in-place hinge connecting the lid directly to the main body. The front incorporates deeply debossed stencil lettering, creating a hollowed-out window effect, while the exterior is textured with an interlocking scalloped "fish scale" pattern to add grip and visual interest. Features Print-in-Place Hinge: Conical pins built into the lid mesh with the box knuckles, requiring no extra hardware. Prints entirely vertically. Scalloped Texture: A geometric overlapping scale pattern is cut into the walls, giving it a stylized organic look. Stencil Lettering: "PIZZARAMA TIPS" is punched completely through the front wall, functioning as a window into the box. Print notes Designed to print in its default orientation (lid standing straight up). Use a 0.2mm layer height or smaller for the hinge gap to function correctly. The floating inner islands of the text will not be supported and are designed to drop away cleanly.
Archiv-Einschub: Schiffe versenken
Ein maßgefertigtes, modulares Schubladen-Regal für Brettspiele und Kartensets (hier ausgelegt auf 150 x 45 mm Boxen). Das Set besteht aus drei Teilen: Regalgehäuse: Eine stapelbare, robuste Außenhülle mit Fase. Schublade: Passgenau mit 0,8 mm Spielraum zum einfachen Herausziehen. Ein Griff an der Front erleichtert das Greifen. Inlay-Buchstaben: Die Schrift ist als 1,5 mm tiefe Aussparung in der Frontplatte angelegt. Die separat gedruckten Buchstaben sind minimal verkleinert (0,15 mm Toleranz) und können nach dem Druck passgenau in die Front eingedrückt werden. Ideal für ein aufgeräumtes Regal, bei dem man jedes Spiel sofort auf der Frontblende erkennt.
BunkMate — Magnetic Rail Tray
A sturdy tray that hangs over a bunk bed rail, keeping bedtime essentials close at hand. Features Magnetic Base: Features eight fully-enclosed pockets sized for 0.7" x 0.12" magnets. Pause your print to drop them in, and they'll be sealed inside the floor forever. Wide Hook: Designed with a 34mm gap to easily clear thicker bed frames. Print-in-Place: No supports required; prints upright with the hook flat on the build plate.
Striped Catchall Tray
A sleek, single-compartment catchall tray designed to hold a phone, keys, and daily carry items. Striated exterior: Horizontal ribs wrap the outer wall for texture and grip. Smooth basin: A flat, un-textured interior keeps delicate screens scratch-free. Low profile: Stands at 18 mm tall to sit neatly on a nightstand or desk.
Edifier Skadis Monitor Stand
A heavy-duty wall stand tailored for Edifier R1280DB monitors on an IKEA Skadis pegboard. I built the footprint wide and deep enough to give the requested clearances all around, using a generous array of integrated T-clip hooks so you don't need any extra hardware to hang it. The sides are braced with closed triangular panels to resist shearing, and I've tucked a thick secondary gusset into the back right corner as requested. Remix Parameters Tray Clearance: Inner footprint sits at 176 mm wide by 232 mm deep, comfortably clearing the Edifiers with 15 mm wiggle room on the sides/front and 21 mm at the back. Front Stop: Raised 15 mm above the base plate. Mounting Pattern: Standard Skadis 40 mm pitch (4 columns, 3 rows). If you prefer metal T-nuts to print-in-place hooks, the backplate is an easy candidate to punch 4.5 mm holes through instead.
Need a part that doesn't exist yet?
Start building →