3D Model Gallery
Every one of these started as a sentence — real dimensions, real holes, print-ready STL. Remix any of them, or describe the part you need and Printy builds it. Start building →
Newest
Circular Floor Reacher
A solid floor reacher designed to slide under scattered objects. The head features a wide flat base with a 180-degree raised wall around the back and sides, naturally corralling items as you sweep them inward. A reinforced boss anchors the stick at a standard sweeping angle, topped with a comfortable T-handle. Remix Hooks This design is a structural starting point. The current parameters fit diagonally onto a standard print bed, but it is built to be adjusted: Stick Length (stick_length): Currently set to 220mm for printability. If you have a larger bed or intend to splice it, bump this up to 600mm+. Head Diameter (head_od): Set at 120mm. Widen it for sweeping larger debris, or shrink it to navigate tight corners. Handle Angle (stick_angle): Sits at 45 degrees. A steeper angle (e.g., 60 degrees) works better if you plan to make it a true standing-height tool. Modular Swap: A quick remix could replace the printed stick with a 22mm socket to accept a standard wooden broom handle instead.
SwiftScoop — Floor Retriever
A sturdy, single-piece scoop designed for retrieving items from the floor. Featuring a wide circular head with a raised back edge and a slightly bevelled front, it slides easily underneath scattered objects. Features Generous Catch Area: 120mm base plate with retaining walls on three sides. Lightweight Core: The shaft is hollowed out to save material and reduce weight. Textured Handle: Raised grip rings ensure secure handling. Printable Size: Scaled down to fit comfortably within a standard 250mm build volume.
Tapered Silicone Depth Stopper
A clean, rotationally symmetrical collar designed to act as a physical limit stop. Built specifically to seat around a cylindrical silicone component, its continuous taper drops from an 80mm base down to a 55mm neck while maintaining a rigid 3mm wall. Design Notes Smooth Contact: Fully rounded 1mm radii on both the upper and lower lips prevent the hard plastic from digging into softer silicone. Unbroken Profile: A simple, continuous exterior taper with no interruptions or decorative elements. Print-Ready: Sits flat on its wide base and requires no supports, hardware, or post-processing.
Ornate Bas-Relief Ceiling Canopy
A plain ceiling canopy is a missed opportunity. When plaster tears out around a fixture box, a flat plastic plate covers the hole but looks entirely utilitarian. This canopy adds an intricate eight-fold radial bas-relief across the visible face, drawing the eye away from ceiling imperfections. Specifications Canopy Diameter: 105mm — wide enough to span a ragged 80mm drywall cut. Ornament Height: Raised 1.2mm off the base surface. Thread Interface: Generous 16.8mm internal thread on the canopy nut prevents binding when threading onto the core hanger. Printability: The entire assembly, including the filigree, sits flat on the build plate and requires no supports.
Deep Trough — Single Feeder
A deep, single-volume wire cage feeder. This updated design drops the middle divider and front perch to maximize internal volume. Perfect for dispensing large amounts of dry feed or hay. Dimensions Width: 3.5 inches (89 mm) Depth: 5 inches (127 mm) Height: 3 inches (76 mm) Features Heavy-duty S-hooks integrated into the rear wall Rounded internal corners for easy cleaning Thicker base (2mm) for durability
Solid Flat-Print Cervical Roll
Most neck rolls are either wobbly two-piece assemblies that snap, or complex curved shapes that require a forest of plastic supports to print. This bridges the gap by making the entire arc a single solid extrusion with a deep, elliptical center channel. It prints completely flat on its side with zero supports, while the swept cut cleanly shapes the flared end into two pronounced horns to catch the occipital ridge. Footprint: 300-degree sweep, ~160mm outer diameter Center Channel: 25mm deep elliptical trough, leaving wide supportive sides Printability: Lies perfectly flat on the Z-plane. Print entirely without supports.
Monolithic Tapered Wrist Rest
A sleek, monolithic wedge that brings ergonomic relief to compact typing setups. Designed specifically for the footprint of a 60% mechanical keyboard, this wrist rest offers a seamless transition from the desk surface to the keys. The stark, minimalist profile features a gentle slope that eliminates harsh edges, providing a clean geometric aesthetic without sacrificing comfort. Design Features Perfect Fit: Spans exactly 295mm wide by 70mm deep to sit flush with compact mechanical boards. Ergonomic Slope: Tapers smoothly from a supportive 18mm back height down to a negligible 4mm front lip. Softened Edges: The top corners feature a subtle rounding to prevent digging during extended typing sessions.
100mm Stepped Cylinder Adapter
A continuous multi-diameter cylinder with a central bore. Features a wide primary section and a narrower stepped shaft, hollowed out by a continuous axial through-hole. Overall Length: 100 mm Top Section: Ø 28 mm × 65 mm length Bottom Section: Ø 14.5 mm × 35 mm length Through-hole: Ø 6.6 mm
Smart Medication Enclosure
A clean, multi-compartment daily pill organiser designed to integrate an ESP32, real-time clock, and 16x2 LCD display. The enclosure is constructed as a single main body carrying all electronics mounts and front-panel cutouts, capped by a spacious three-chamber medication tray. Three independently hinged lids (Morning, Afternoon, Evening) running on standard 1.75mm filament pins Generous component cavity below the pill chambers for simple wiring M3 machine screw assembly throughout with flush countersinks Ample mechanical clearance on the hinges to guarantee a smooth swing straight off the build plate
Industrial Right-Angle Shim
A flat, right-angled spacer designed to sit exactly flush on top of an existing table leg bracket. It levels uneven furniture by adding a precise 3mm offset without altering the original hardware or changing the footprint of the joint. Dimensions Outer leg lengths: 105 mm Arm width: 30 mm Thickness (offset): 3 mm
Spiral Slow Feeder Cat Bowl
A 180mm slow feeder bowl featuring an internal spiral maze, designed to pace eager cats who inhale their food. The layout uses a 40mm pitch Archimedean spiral of 15mm tall bumps, creating a continuous winding channel that forces pets to work for their kibble instead of gulping it. Remix Parameters & Tuning Bowl Dimensions: Starting at a 180mm outer diameter and 45mm total height (40mm internal depth). Easy to scale down for smaller portions or up for dogs. Spiral Pitch: The 40mm pitch defines the main track width. Adjusting this value directly changes the difficulty and accommodates larger kibble sizes. Bump Density: Currently populated with 24 rounded bumps, each standing 15mm tall. Modifying the bump count tightens or loosens the spacing along the track. Post-Processing: Best paired with food-safe materials like PETG. For long-term daily use, consider sealing the finished print with a food-safe epoxy to smooth out layer lines and make washing easier.
Combustion Engine 53mm Oval Vent Plug with Grip
A potential plug for mount when removing the Combustion Engine.
Nose-Down Controller Charging Cradle
A heavy-base desktop cradle designed to hold a standard Xbox controller nose-down while resting securely on its grips. It keeps the charging port accessible from below, maintaining a constant connection with a play-and-charge cable so the battery is fully charged before the next boss fight. Angled resting pocket holds the controller by the grips, featuring lateral retaining walls to prevent sliding. Central 70mm void clears the controller's nose, triggers, and bumpers. Bottom routing channel accommodates standard charging cables, feeding directly upward into the port. Flared rear cable entry allows for smooth wire management. Sized specifically to fit standard 155mm wide gamepads.
Montana keychain
A 50×20mm solid fob block featuring a standard 4.5mm through-bore on the left flank, properly sized to clear 4mm jump rings or standard split rings without binding. Clearances: The bore is positioned to leave exactly 4.75mm of solid wall at the left edge. Chassis: Base deck sits at exactly 3.0mm thick, laying completely flat on the build plate. Emblem: A classic bowtie geometric profile raised 0.8mm above the base, bringing overall thickness to 3.8mm. Fits standard key rings, though heavy-duty 5mm carabiner hooks will not clear the bore.
PK360 Combustion Engine adapter
Allows connecting combustion engine grill fan to a pk360 grill intake vent
TrailBase — Gladiator Tablet Dock
The TrailBase brings your digital command center directly to your Jeep Gladiator's dash. Designed to sit securely against the AC ledge, this low-profile tablet dock utilizes 3M VHB tape and a recessed magnetic pocket to keep your device locked in place over rough terrain. The open-front bezel design ensures full screen visibility while maintaining a rigid, drop-in structure for quick mounting and dismounting on the trail. Features Secure Stance: Deep bottom ledge maximizes adhesion surface for 3M mounting tape above the AC vents. Magnetic Retention: Rear block houses a flush rectangular magnet pocket for supplemental pull. Cable Ready: Open bottom channel allows for continuous charging while docked. Drop-in Slot: Tolerance-optimized rails make inserting and removing the tablet seamless.
86mm Windowsill Tomato Seedling Tray
12-cell starter tray dimensioned for narrow residential windowsills. Fits a standard 86mm or deeper sill plate. Do not attempt to balance this on half-depth ornamental ledges; the 253mm overall length requires a completely flat run to avoid stressing the joined top lip when loaded with wet soil. Fitment Specs Clearance Required: 86mm (W) x 253mm (L) minimum flat sill surface. Cell Dimensions: 50mm depth. 40mm square top bore tapering to a 32mm base. Extraction: 1.2mm floor thickness permits mechanical release of the tomato soil plug via bottom pressure. Drainage: Single 8mm center bore per cell. Will drain immediately onto the host surface—must be paired with an 86x253mm minimum drip pan.
Motorized Clamshell Medication Box
A clean, professional enclosure for a motorized medication reminder. The enclosure is split into two zones: a full-height front bay for electronics (ESP32, LCD, RTC, and battery), and a clamshell medicine compartment in the rear. Clamshell Box: The medicine bay splits exactly in half, providing deep trays in both the base and the lid. Electronics Integration: Dedicated cutouts for a 16x2 LCD, LEDs, a buzzer, switch, and side Type-C port. Motorized Hinge: Integrated M3 hinge knuckles and servo mount designed for an SG90. No Supports: All parts print flat on the bed.
1602 / SG90 Medication Dispenser
A complete electromechanical housing built around a standard 1602 LCD and twin SG90 servos. The rear section is split into upper and lower decks: the upper deck holds four gravity-fed medicine hoppers, which drop through a shelf into a dual-funnel lower bay that deposits tablets into a single central collection cup. Fitment and Clearances Actuators: Dual 23×12 mm mounting blocks in the rear base fit standard SG90 9-gram servos. Tolerances: The slider tracks inside the hoppers are 2.5 mm tall for a 2 mm gate, leaving 0.5 mm of vertical clearance to prevent binding on FDM prints. Linkages: Each slider gate has a 3 mm peg designed to take standard servo pushrods. Electronics: Front bay handles a standard 1602 display, KCD11 rocker switch (15×10 mm bore), and a Type-C TP4056 board. Check your servo horn sweep radius before committing to the print — if you are using extended horns, you may need to clip them to clear the internal dividing wall.
Tumbling Travel Soap Box
A heavy-duty soap container designed for gym bags and travel. The deep 8mm friction-fit lip prevents accidental opening when tumbling around, while integrated 5mm ribs on both the top and bottom interior surfaces keep the soap suspended out of any pooled water, no matter which way the case ends up facing. Integrated Ribs: 5mm tall standoffs in both halves ensure the soap dries evenly. Deep Closure: An extended interior lip locks the lid securely in place without extra latches. Two-Piece Design: Eliminates loose inserts that could rattle or fall out during use.
150mm Ribbed Vase Shade
A solid geometric form designed specifically for spiral vase-mode printing. The shape tapers from a 50mm base to a 130mm midsection, closing back down to 70mm at the top. The surface combines 8 primary twisting sweeps with a secondary ribbed texture (48 minor ridges) overlaid on top. Print Notes Intended for spiral vase mode — the model is completely solid. Zero out your top layers in the slicer to leave the form open. Check your extrusion width; thicker lines will give the shade more rigidity.
Pendant Ceiling Canopy
A clean, three-piece ceiling canopy designed to bridge a jagged hole and manage a pendant cable. The mechanism borrows from standard flat-pack fixture hardware: a central core hangs from the ceiling hook and threads through the main cover, while a hex nut clamps the cover tight against the drywall. The core is hollow to let your two-wire cable pass through cleanly, with side-exits at the top so the wiring doesn't foul the hanging eyelet. Features 105mm Canopy: Leaves a comfortable margin over an 80mm hole to hide chipped plaster. Hollow Core: 8mm internal channel easily clears standard twin-core lighting cable. Thread Clearance: The nut is cut with an oversized 16.8mm thread for a smooth, bind-free fit on standard FDM prints. Support-Free: All three pieces sit flat on the bed and require no supports to run.
BenchWeigh — Micro Scale Chassis
A straightforward two-piece chassis designed to house a standard 75mm 1kg load cell, an HX711 amplifier, and an ESP32 dev board. The base unit includes a raised 6mm pedestal to secure the fixed end of the load cell, giving it the clearance it needs to deflect. A walled rear compartment keeps the amplifier and microcontroller contained, with a side cutout for routing cables to the load cell. The weighing platform is printed alongside it; it features a matching pedestal for the floating end of the load cell. Dimensions Base Footprint: 120mm × 80mm Weighing Platform: 100mm × 80mm Load Cell Pedestals: 25mm × 16mm × 6mm Electronics Bay: 105mm × 35mm (internal) Print notes Both parts print flat on the bed. The screw holes are spaced at 15mm for standard M4 bolts and include 3mm counterbores on the print surfaces so the screw heads sit flush when assembled. The platform flips over to mount onto the floating end of the load cell.
Sweeping Crane Shoe Horn
Rising from a generously cupped heel like the neck of a sweeping crane, this half-meter-long shoe horn bridges the gap between hand and floor. The elongated, curving silhouette is designed for bodies that prefer to remain upright, translating a gentle pull into a perfectly seated heel without demanding a painful forward fold. The structural arch provides rigidity along its substantial length, ending in a flared, comfortable grip. Form & Function The Reach: 500mm of unbroken length to save the lumbar spine from unnecessary contortions. The Scoop: A 60mm wide, smoothly radiused curve shaped to comfortably embrace a heel without pinching. The Roost: A 10mm hanging hole at the crest of the handle keeps it suspended and accessible on a closet hook.
Need a part that doesn't exist yet?
Start building →