3D-printable home fixtures & hardware
Brackets, cabinet pulls, knobs, doorstops, racks and mounts built to real measurements. Browse what makers built, or describe the exact fixture you need and Printy makes it.
Need one that fits your exact measurements? Start building →
Newest
Appendiabiti a Traliccio 32mm
Appendiabiti rigido a parete stampabile in 3D. Disegnato con un profilo sagomato per ridurre il consumo di filamento mantenendo un'elevata resistenza al carico. Interasse: 32 mm esatti. Fori: 3,2 mm (per viti da 3 mm), con svasature da 4,5 mm posizionate a profondità fissa. Accessibilità: tunnel orizzontali da 8,5 mm per inserire agilmente vite e cacciavite. Orientamento: Da stampare rigorosamente coricato sul fianco per sfruttare la direzione dei layer.
Tank Tap Bulkhead Fitting 1 1/2" BSP
A through-wall bulkhead fitting in the spirit of a classic water butt tank connector: a broad round flange sits against the tank wall, a long threaded barrel passes through, and a matching lock nut clamps it from the other side. 72 mm flange with a shallow gasket seat for a flat washer or O-ring 1 1/2" BSP-style male thread (47.8 mm major diameter, 11 TPI), 40 mm long 38 mm through bore Separate lock nut, printed alongside Design notes: The thread is a generic approximation of the Whitworth form, so test-fit against your mating part. Cut the tank hole to suit the thread, and use a rubber gasket against the flange. Print the flange face-down; PETG is a sensible choice for water contact.
Halterung mit Gegenstück für Hue-Lampe
Zweiteiliges Set: eine 170 × 45 mm Halterung mit zwei Befestigungslöchern und zwei Steckblöcken sowie ein Gegenstück mit Steckfassungen und einem Klipp-Tunnel für eine quer liegende Hue-Lampe (44 × 36 mm). Beide Teile sind auf Stabilität ausgelegt: dickere Grundplatte, breiter konischer Blockfuß, kräftige Fassungswände und eine dicke Wand über dem Tunnel. Halterung: Platte 8 mm, Blöcke 20 × 20 mm mit konischem Fuß (40 mm unten) Gegenstück: Fassungen mit etwa 6,7 mm Wandstärke, Sockel 70 mm breit Tunnel 44,8 × 36,6 mm, unten offen zum Einklipsen Querbohrungen 5 mm bzw. 5,4 mm Empfehlung: PETG, mindestens 3 Wandlinien, 40 % Infill
Twisted Planter With Name Plaque
A 100mm base hexagonal planter with a deep twist and a prominent front plaque. The planter features a solid 5mm-thick wall that precisely tracks the exterior twist, terminating in a flared rim. It includes a central 8mm drainage hole alongside five 10mm perimeter holes. A pill-shaped plaque sits seamlessly flush on the front face, equipped with extruded placeholder text ("NAME") that will export as part of the geometry—ideal for setting up multicolour text in your slicer. Check your drip tray to ensure the 100mm base clears the lip.
Piedino Subwoofer in TPU
Piedino antivibrazioni da 60 mm progettato per subwoofer, con geometrie ottimizzate per l'assorbimento acustico se stampato in TPU. Diametro: 60 mm Altezza: 25 mm Fissaggio: Foro centrale da 5 mm (ideale per viti da 4,5 mm) con svasatura, compatibile anche con montaggio a biadesivo Design: Scanalature concentriche sul fondo per aumentare la flessibilità del materiale e isolare le vibrazioni dal pavimento
Moderne Zweifarb-Pflanzenschilder
Diese drei Pflanzenschilder kombinieren ein sauberes, zweifarbiges Layout mit einer robusten Konstruktion. Der Grundkörper misst 160 mm in der Gesamtlänge, wobei ein verstärkter Erdspieß für sicheren Halt im Substrat sorgt. Der doppelte Rahmen und die moderne serifenlose Schrift heben die Beschriftung ("White Widow" und "The Church") deutlich hervor. Design- und Druckhinweise Zweifarbdruck: Konzipiert für einen Filamentwechsel ab Z-Höhe 2,0 mm. Der Grundkörper bildet das Bett, während Ränder und Text als 0,8 mm starke Akzente aufsitzen. Verstärkung: Eine konisch zulaufende Mittelrippe auf dem Erdspieß verhindert ein Abknicken in dichter Erde, ohne den Druck zu verkomplizieren. Keine Stützen nötig: Die Schilder liegen komplett flach auf dem Druckbett und können direkt nacheinander oder gleichzeitig gedruckt werden.
DraftBlock — Snap-Fit Vent Cap
A solid plug designed to completely seal an unused round vent or duct. The cover features a flat profile with softly rounded outer edges, hiding the internal void entirely. Features Snap-Fit Mounting: Four downward-facing flexible clips grip the inside of the duct securely. Print-Optimized: The clips are thick enough to provide tension but long enough to flex without snapping in PLA or PETG. Low Profile: Sits just 3 mm proud of the wall or floor line.
Flat-Backed Angled Wall Hook
A 3D-printable wall hook featuring a straight outer spine for a clean visual line against the wall, paired with a curved inner profile that creates a natural resting notch. Straight spine: Sits perfectly parallel to the mounting plate. Inward curve: Adds depth to the hook's catch without thinning the whole shaft. Base plate: 30x30 mm, sized for standard mounting tape.
64mm Hose Holder Clamp
What it's for A heavy-duty saddle clamp designed to securely mount a 64 mm outer-diameter hose. The clamping mechanism uses an M6 bolt and a captive nut on the right ear to tighten the split ring. Dimensions Bore: 64 mm unobstructed passage. Base: 74 mm wide by 70 mm long, 6 mm thick. Mounting holes: Four 6.5 mm clearance holes at the corners. Clamp width: 25 mm thick on the Z-axis. Print notes Print this flat on its base. The hex recess is sized for a standard M6 nut and should bridge without supports on well-tuned printers, but a tiny dab of support inside the hex pocket won't hurt.
Smart Duplex Sconce Plate
An oversized, deep-shell wall plate for a standard US duplex outlet, built to house a Raspberry Pi Zero W and up-and-down sconce lighting. Pi Zero Mount: Integrated standoffs (58x23mm spacing) for M2.5 screws, tucked beside the receptacle. Lighting Control: 5.5mm face cutout for an ambient light sensor. LED Bays: Top and bottom mounting blocks with flush cutouts for dual-directional LED strips. Clearance: 14mm overall depth clears standard hardware while providing internal routing space.
30mm Fluted Drawer Knob
A mushroom-style drawer knob with a straight-fluted grip ring. Designed for environments where hands may be wet, the flutes provide mechanical grip without the complex recesses of a diamond knurl that trap moisture. The part includes a central clearance hole for standard M4 mounting screws. Specifications Cap Dimensions: 30 mm diameter, 18 mm tall Stem Dimensions: 12 mm diameter, 10 mm length Total Standoff: 28 mm Mounting: M4 clearance through-hole (4.5 mm diameter) Grip Feature: 30 vertical flutes
Płyta 18mm Nóżka Kątowa 150mm
Nóżka oporowa pod standardową płytę meblową 18 mm. Gniazdo ma 18,6 mm szerokości, co daje luz roboczy pozwalający wsunąć krawędź płyty bez rzeźbienia materiału, z pełnym prześwitem na wylot (brak ścianek czołowych). Dno kanału opada pod kątem, dając około 3 mm różnicy wysokości na 30-milimetrowym odcinku chwytu. Podstawa została rozszerzona do 45x45 mm – przy 150 mm całkowitej wysokości prosty słupek nie utrzymałby obciążeń bocznych. Wymiary montażowe Kanał U: 18,6 mm szerokości, 40 mm głębokości (w najpłytszym miejscu). Mocowanie: Dwa otwory przelotowe 4,5 mm z fazowaniem pod wkręty z łbem stożkowym, rozstaw 14 mm. Wysokość całkowita: 150 mm. Kąt dna: Spadek 3 mm na 30 mm długości profilu. Pasuje do gołych płyt 18 mm (wiórowa, MDF, sklejka). Nie wciśniesz w to płyty 22 mm, a z płytą 16 mm wkręty po obu stronach będą musiały ściągnąć ścianki kanału, co grozi pęknięciem wydruku. Przed drukiem upewnij się, że 3 mm spadek na dnie to właściwy kąt dla twojej zabudowy.
280mm Irrigation Controller Enclosure
A rigid 280 × 200 × 90 mm printed enclosure designed specifically for an ESP32-based multi-zone plant irrigation controller. The layout divides the internal volume into three distinct areas: high-current power distribution on the left, six MOSFET drivers in the center, and the low-voltage microcontroller logic on the right. An extra-wide central cable channel runs between the two rows of MOSFETs, and all high-traffic access areas—like screw terminals and adjustment dials—have generous working clearances. The outer walls feature deep U-slots for cables, cut from the top edge so the main flat lid traps them cleanly in place without relying on separate cable glands. Internal Layout details Zone A (Power): Mounts for a 56×35 mm DC-DC buck converter, a friction-fit bracket stack for four WAGO 221-415 lever connectors, and a C-clip for an inline 5A barrel fuse. Zone B (Switching): Two rows of custom mounts for six 35×32 mm MOSFET boards. Each uses exactly two diagonal standoffs to leave maximum free space around the terminals. Zone C (Control): Stand-offs for an ESP32 NodeMCU, with a dedicated USB-C opening aligned in the external right-hand wall. Structure: Embossed floor labels mark all hookup zones. Cable tie bridges are scattered throughout the base for organization, and vertical ventilation slots flank the rear and sides. Uses four M3 screws driven directly into heavy internal corner bosses to seal the lid.
9-Inch Planter Drainage Raiser
A structural insert built to elevate a 9-inch plastic nursery pot inside a decorative ceramic planter. Standing 3 inches tall, it provides a solid base while allowing standing water to drain clear of the roots. The top deck uses a concentric ring and spoke pattern — significantly stronger and faster to lay down than a square grid. The load is carried outward to four tapered pillars set directly under the main intersections. Remix Hooks Total Height: Built at 76.2 mm (3 inches), but the leg pillars can be stretched or squished to match any outer pot depth. Deck Thickness: Starts at 6 mm to handle a 20 lb load without bowing. Leg Taper: Set at 24 mm at the base narrowing to 18 mm at the top — widen the base if you need it to sit on a softer medium instead of a hard ceramic bottom.
Brutalist Pipe Insert
A heavy-duty ventilation insert featuring an integrated square mesh. The single-ended flange acts as a firm stopping collar, while the dense internal grid blocks debris and insect ingress without severely choking airflow. Designed as a drop-in piece for 80 mm bulkheads or exhaust pipes. Design Notes Mesh: 3x3 mm openings with 1.5 mm solid bars Interface: 80 mm main outer diameter with a 2 mm wall Collar: 5 mm thick flange to prevent over-insertion Printability: Single solid body, optimized for FDM without supports
Straight Cylindrical Pipe
A straight cylindrical pipe with a uniform wall thickness, designed for fluid transfer, structure, or sleeving. Inner Diameter: 60 mm Outer Diameter: 64 mm Wall Thickness: 2 mm Overall Length: 60 mm
64mm Straight Cylindrical Pipe
A straight cylindrical pipe designed for flow or structural use, featuring a centered continuous bore. Inner Diameter: 60 mm Outer Diameter: 64 mm Wall Thickness: 2 mm Length: 60 mm Prints vertically without supports.
Ground Spike Cup Base
What it's for A heavy-duty circular base with an integrated ground spike, designed to hold poles, pots, or yard fixtures securely in the grass or dirt. The spike uses a cruciform (fin) shape to maximize holding power in the soil while saving plastic. Dimensions Overall footprint: 115 mm diameter Base height: 25 mm Inner pocket: 65 mm diameter, 20 mm deep (leaving a 5 mm solid floor) Spike length: 80 mm Print notes For best results, rotate the model 180 degrees in your slicer so the flat top of the base sits on the build plate and the spike points straight up. This allows the entire part to print without supports.
60mm Straight Hollow Pipe
What it's for A standardized straight hollow cylindrical pipe segment. Suitable as a structural spacer, a fluid/air channel, or a sleeve for cables and smaller tubes. The uniform 2mm wall is optimized for standard FDM printing parameters. Dimensions Outer Diameter: 60 mm Inner Diameter: 56 mm Wall Thickness: 2 mm Total Length: 60 mm Remix ideas Add flanges or threads to the ends for modular connection. Introduce a longitudinal slit to use it as a snap-on cable cover. Thicken the walls if intending to use under compressive loads.
Baton 4 Pro Glowing Pumpkin
A diffuser for the Olight Baton 4 Pro. Open-faced diffusers let too much harsh light through, ruining the effect. This version leaves a 0.8mm thin wall across the eyes and mouth, keeping the bulb hidden while letting the face glow when powered on. Fit: 26.5 mm inner diameter collar for the Pro head. Walls: Main shell is 2 mm thick, face cutouts step down to a 0.8 mm membrane (two standard perimeters).
Acoustic Cabinet Sealing Plug
A tailored sealing plate built to cap off a 48 mm port while cleanly passing through four heavy-gauge wires. The stepped rear boss drops straight into the MDF cutout, leaving the broad outer flange to hold the seal tight against the cabinet face. Build Details Main flange: 75 mm diameter Alignment boss: 48 mm diameter (8 mm depth) Routing ports: Four centered holes sized for 2.5 mm² speaker wire Hardware: Countersunk for 3 mm fasteners on a 43 mm square layout
Reinforced 8mm Irrigation Y-Splitter
A heavily reinforced Y-shaped hose connector built specifically to merge two fluid lines into one. Designed for 8mm inner-diameter flexible tubing, it uses a solid central hub rather than thin overlapping walls, ensuring the part handles pressure without snapping at the junction. The internal geometry is sculpted to maintain flow: a 6mm channel through the main body prevents a bottleneck at the merge, smoothly necking down to 5mm inside the barbs to guarantee thick, watertight perimeters where the plastic gets thinnest. A precision flat cut on the underside allows the entire assembly to drop straight onto the build plate, completely eliminating the need for support material. Remix Hooks & Constraints Hose Fit: The double barbs peak at 8.5mm OD and drop to a 7.2mm valley, grabbing 8mm ID silicone or vinyl hose tightly. Print Settings: Built for PETG or ABS. Use 4 to 5 perimeters to ensure watertightness and maximum mechanical strength against bending forces. Scaling: Scaling up works cleanly for larger hose (e.g., 125% for 10mm ID), but scaling down is not recommended as the internal channel will restrict flow and the walls may drop below the required thickness for a watertight seal.
Compact 90-Degree Elbow Pipe
What it's for A highly compact 90-degree pipe elbow designed to route fluids or air in tight spaces. Instead of a long, sweeping plumbing radius, this model pulls the corner in as tight as physically possible—bringing the outer inner corner to a sharp point while maintaining a 2 mm smooth transitional radius on the interior flow path to prevent sharp turbulence. Dimensions Outer Diameter: 60 mm Inner Diameter: 56 mm Wall Thickness: Constant 2 mm Straight Sections: 30 mm on each end Print notes Orient the pipe flat on its side (as positioned by default) to print entirely without supports. A brim may be helpful depending on bed adhesion, though the large flat contact patch is usually sufficient.
Silicone Sealing Washer
This is a flexible sealing washer designed to fit between a tap adapter and a tap connection. It provides a watertight seal when compressed. Dimensions Outer Diameter: 28 mm Inner Diameter: 20 mm Thickness: 3 mm Material Notes While modeled here as a solid, the physical part should be printed in a flexible filament like TPU, or cast in silicone, to function as a proper seal.
Need a part that doesn't exist yet?
Start building →