3D-printable home fixtures & hardware
Brackets, cabinet pulls, knobs, doorstops, racks and mounts built to real measurements. Browse what makers built, or describe the exact fixture you need and Printy makes it.
Need one that fits your exact measurements? Start building →
Newest
Dragon Head Blind Cord Cleat
Blind cords slip off a plain cleat the moment the tension changes. This dragon head cord cleat has a tusk on each side of the snout, so the cord wraps under it and stays put. Mounting plate: 30 x 70 mm, 4 mm thick, two countersunk screw holes Tusks: ball-tipped, project about 16 mm out from the centre on each side, above the cord path Cord slot: 3.5 mm tall, runs left to right through the snout Flames: three tongues from each nostril, pointing forward over the plate Extras: horns, brow ridges, cheek spikes Print: plate flat on the bed; the horns and flames are small overhangs, so a little cleanup or supports may help
Konischer Rohradapter 34 auf 26 mm
Konischer Rohradapter, 65 mm lang, mit gleichmäßiger Verjüngung von Innen-Ø 34 mm auf Innen-Ø 26 mm. Die Stirnkanten sind mit 1 mm Radius abgerundet, damit die Oberfläche glatt ist und sich Schläuche leichter aufstecken lassen. Länge: 65 mm Innen-Ø Anfang: 34 mm, Innen-Ø Ende: 26 mm Außen-Ø Anfang: 40 mm, Außen-Ø Ende: 32 mm Wandstärke: 3 mm (horizontal gemessen) Kantenradius an den Stirnseiten: 1 mm Druck: stehend auf der großen Öffnung, ohne Stützen
Lifebuoy — Wall Key Rack
Lifebuoy is a wall-mounted key rack shaped like a beach lifeguard buoy, with a red body, white LIFEGUARD lettering and five sturdy hooks. Features 230 mm long stadium-shaped body, 70 mm tall, 14 mm deep Letters as a separate white piece set into a pocket in the red body Five round-tipped hooks along the lower front Two rear keyhole-style screw holes with counterbores Flat back for printing without supports Print notes Print the body and the letters in separate colours (PLA, 0.4 mm nozzle), back face down.
Wavy Bobby-Pin Sock Clip
A oversized bobby-pin style clip for keeping sock pairs together in the wash, with a J-shaped hook for hanging on a drying rack. Printed flat as one piece. Remix hooks Wave count and depth: 3 waves at 1.5 mm amplitude. Raise the amplitude for more grip, lower it for a straighter pin. Arm width and thickness: 3.6 mm wide, 4 mm thick. Thinner arms flex more. Opening: 8 mm gap at the bulbed tips, tapering to closed at the top. Widen it for thick socks. Hook radius: 15 mm. Enlarge it for thicker rack rails. Pairs well with a mesh laundry bag. The clip section is 70 mm long and about 15 mm wide. The hook sits above that.
G 1 1/4" Plug with Concave End
What it's for A male-threaded plug for a G 1 1/4" (BSP parallel) port, such as a bull nose fitting. The end face is dished (concave) so it seats against a rounded nose. Dimensions Thread: G 1 1/4", 41.91 mm major diameter, 2.309 mm pitch (11 TPI) Thread length: 20 mm Hex head: 50 mm across flats, 10 mm tall Concave dish: 30 mm sphere radius, 5 mm deep Remix ideas Change the dish radius or depth to match a different nose profile. Add a gasket groove under the hex head. Swap the hex for a knurled round head for hand tightening.
108 mm Vent Grille Cap, Center-Rib Clearance
Closed 108 mm rounded-square cap for an installed round vent grille (about 99 mm body, 108 mm flange), with a dedicated recess over the raised center rib. Fit Fits over: round grille up to about 100 mm, flange up to about 101.5 mm square. Face: 4 mm, fully closed. Cavity: 100.5 mm round, 15 mm clearance above the grille, plus a 24 mm wide channel along X reaching 21 mm clear. Lip: 10 mm deep, 3 mm walls, 102 mm pocket, eight small friction bumps. Check before printing Measure the center rib's height and direction. The channel assumes it runs along X and stays under about 18 mm tall. Not compatible Flanges over 101.5 mm square or grilles wider than 100 mm.
Bote de basura innovador
Bote de basura con tres compartimentos para orgánicos, reciclables y basura general. Evita que todo termine mezclado en una sola bolsa y que haya que tocar la tapa con las manos sucias. Cada compartimento tiene su propia abertura con trampilla de color. Dos sensores al frente detectan a la persona que se acerca, una pantalla indica el nivel de llenado, un panel solar inclinado en la parte trasera alimenta la electrónica y cuatro ruedas permiten moverlo. Datos clave Diámetro del cuerpo: 240 mm; altura total sin panel: unos 346 mm Tres sectores de 120° separados por divisiones de 3 mm Aberturas de 76 mm de diámetro, una por compartimento Ruedas de 36 mm en cuatro soportes Impresión por piezas: cuerpo, tapa, chasis, ruedas y panel; paredes de 3 mm, sin soportes en el cuerpo La electrónica (sensores, pantalla, motores) no está incluida: el modelo solo aporta alojamientos y forma
Figure8 — Clip-On Cord Winder
Figure8 is a compact cord winder that snaps onto the flex of a kettle, toaster or similar appliance and takes up the slack. Wrap the spare cord around the two end horns in a figure-eight pattern, and the curled horn tips hold the turns in place so the wrapped cord can't spring loose. It is designed for cluttered counters where appliance cords tend to tangle. The spine carries a round channel with a narrower snap-in slot, so the winder stays on the cord instead of sliding off. The cord is pressed through the slot, and the lips flex to let it pass. Dimensions Overall length: 80 mm Overall width: about 46 mm across the horns Height: 9 mm Cord channel: 5 mm diameter, running the full spine Snap-in slot: 4 mm opening Features Four horns with tips curled back toward the centre Chamfered spine edges Single-piece body with no assembly Compatibility Intended for standard 6–7 mm appliance cords, which squeeze through the slot and sit snugly in the channel Print notes PETG or TPU is recommended, since the slot lips need to flex Stiff PLA may crack at the lips when the cord is pushed in Prints flat on the bed; the curled tips are short, so supports are only needed if the slicer flags them
Under-Sink Bag Roll Dispenser Barrel
A grocery-store bag-roll dispenser, shrunk down and bolted under the sink. A snug barrel holds a 60 mm roll of trash bags, and the next bag's edge hangs out of a slot in the bottom, ready to grab. A serrated lip along the front of the slot tears each bag off cleanly, so there's no more digging for the end of the roll. The barrel is closed at one end and open at the other. A separate press-fit end cap seals the open end once the roll is loaded. Design notes Bore: 64 mm diameter for a 60 mm roll, with 3 mm walls. Length: 130 mm overall. Dispensing slot: 20 mm wide, running along the bottom of the barrel. Tear lip: a row of downward-pointing teeth at 4 mm pitch on the front edge of the slot. Mounting: a flat back plate with two countersunk screw holes. The holes sit above the barrel, so screws never cross the bore. End cap: printed as its own piece, with a plug that fits the bore and a flange that matches the barrel. Print and remix notes The teeth are the lowest points as modelled, so plan on supports under the barrel. Printing the part on its back plate is an easy re-orientation. Slot length, tooth pitch and screw spacing are the obvious values to adjust for other roll sizes or cabinet layouts.
Script Plaque Planter Pot
A sturdy, functional planter featuring a prominent top rim and built-in bottom drainage. The outer face is permanently marked with custom lettering set directly into the curvature of the main body, ensuring the script perfectly traces the cylinder. Drainage: Five distinct bottom holes prevent water pooling Structure: Thick walls and a reinforced lip for easy handling Engraving: Carved to a uniform, shallow depth across the curved face
Railing 2 m Long, 1.5 m High
A railing panel with the dimensions written on every part, so nobody has to dig out a tape measure to check which bar is which length. Overall: 2000 mm long, 1500 mm high, 50 mm deep Posts: 50 x 50 mm, 1500 mm tall, labelled with height Top and bottom rails: 1900 mm between posts, 80 mm tall Bars: 12 vertical bars, 20 x 20 mm, 1260 mm long, 150 mm centre-to-centre Labels: raised 1 mm text on the front face (top rail length, 150 mm gap marks, bar lengths, post heights) Printing: designed at full size, so scale down or split into sections for a normal printer
Wide Hook With Tall Front Lip
A small wall-side hook, 20 mm wide and 15 mm deep, with a 20 mm back plate, a flat 3 mm arm and a 50 mm upturned front lip. Remix hooks Width (20 mm): the one value shared by the plate, arm and lip. Widen it for heavier loads or narrow it for tight spots. Lip height (50 mm): lower it to around 10–15 mm for a simple catch, or keep it tall to hold flat items upright. Back plate height (20 mm): raise it to leave room for a screw hole or two. Arm thickness (3 mm): thicken it if the hook will carry weight. Pairs well with countersunk screw holes in the back plate or double-sided mounting tape.
HexGrip — Square-Cut Plywood Hex Clips
HexGrip is a two-clip press-fit system for building hexagonal shelving from 1/2 in plywood, now designed for plain 90° square-cut panel ends. Each slot ends in a solid stop 5 mm from the vertex centre, so neighbouring panels meet at 120° without colliding and no mitre cuts are needed. Features End Cap Clip: two slots at 120° for outer hexagon corners. Spoke Clip: three slots 120° apart for shared vertices in a hexagon network. Barbed slot walls with about 0.55 mm interference per side: ramped entry, steep faces that resist pull-out. Dimensions Slot width 13.0 mm, depth 19 mm Clip height 24 mm, arm length 30 mm Print notes Prints with the slot opening facing up, no supports needed. A single hexagon uses 12 clips, one on the front and one on the back of each vertex. Print one first to check the fit against your actual plywood thickness.
Cricket Calcium Duster Tube With Inner Screen
A cricket calcium duster tube that keeps powder in one end and crickets in the other. Crickets get dusted when the tube is shaken, because the powder passes up through a screen. The fix is a threaded screen collar between the tube and the powder cap, so nothing prints inside the tube. Key numbers (75% scale) Tube: about 56 mm outside diameter, about 115 mm long, walls about 1.9 mm Threads: about 3.75 mm pitch, same thread on all pieces, so the caps are interchangeable Screen collar: 19 round holes, about 4.5 mm each, in a separate print Powder cap: deep cup for powder, threaded only at the rim Stop flanges: on the tube, so caps seat at a fixed depth Printing Prints open end up, no supports needed PETG recommended, 0.28 mm layers, 10 to 15% infill Four separate parts: tube, powder cap, cricket cap, screen collar
Toolbox Front Latch Replacement C-Clip
Replacement front latch for a STUFF Basic 20 inch toolbox, for when the original hinge loop or hook has snapped. One solid C-profile part, 61 mm wide, with an open clip at the bottom that snaps onto the box pin and a filleted L hook at the top. Key numbers Overall: 61 mm wide, 65 mm tall, 18 mm deep Wall: 5 mm throughout Clip: 5.3 mm bore, 15.3 mm outer diameter, 5 mm gap Hook: 13 mm forward, 5 mm inside fillet, 2 mm outside fillet, 2.5 mm rounded tip Printing Material: PETG Supports: none Orientation: lay it on its 61 mm side so the C-profile faces up
Round Dovetail Splash Guard
A heavy-duty 20-inch circular splash guard split into quarters. It features a continuous 4-inch tall outer rim and interlocking dovetails to snap securely around a 2-inch pipe.\n\n### Tweaking the Design\n Rim: Set at 4 inches tall and a half-inch thick. You could easily lower the rim to save plastic if you don't need the full basin volume.\n Clearances: The dovetails have a built-in 0.3mm tolerance. You can widen that if your printer leaves heavier seams.\n* Joints: Three 36mm-wide dovetails lock each quadrant. For a permanent install, add a little silicone to the seams before pressing them together.
Matilda sign 2
What it's for A door sign reading "Matilda's room" in raised script lettering on a flat plate with a screw hole at each end. Dimensions Plate: 160 × 66 × 4 mm, rounded corners Lettering: raised 2.5 mm, Satisfy font, two lines Two 5 mm screw holes near the ends Remix ideas Swap "room" for another word Change the font or colours Add a hanging hole at the top instead of side screws
горшок илья
A solid-walled, 140mm tall flower pot with subtle vertical waves along its tapered exterior. The base tapers from a 120mm top opening down to 105mm at the bottom, featuring a robust 4mm thick floor and exactly eight 6mm drainage holes to keep soil adequately drained. Remix Hooks Wall Thickness: Currently 3mm, cleanly subtracted from the inner radius so the exterior waves never break through. Wave Amplitude: Set to 1.5mm with 24 peaks around the perimeter; you can scale the amplitude up for a deeper scallop or increase the frequency for a ribbed texture. Drainage Pattern: The 8 holes sit on a 60% radius ring; this is an easy block to swap out if you prefer a slotted grid or a single large center hole. Scale Factor: The linear extrusion uses a calculated 120/105 ratio. Tweaking this lets you flare the pot wider or pull it into a straight cylinder.
120mm Wavy Suspended Planter Pot
A contemporary, self-supporting planter insert designed to seat perfectly into a matching 130mm water reservoir. The exterior features a 12-point wave pattern with a gentle 45-degree sweeping twist, merging seamlessly into a robust 120mm upper resting lip. The interior taper mirrors the outer walls to maintain a reliable 2.5mm thickness, finishing with an elegant inner flare at the rim. Specifications Dimensions: 140mm height, 120mm max outer diameter (at the rim). Clearance: Tapered base drops to ~107mm diameter to comfortably clear standard 130mm reservoir walls. Drainage: Seven 5.5mm functional ports arranged flush to the floor. Printability: The support lip is carried by a calculated 45-degree transition collar, ensuring the overhang prints completely clean without supports. Drops right onto the build plate.
Botanical Propagation Tray
A shallow, rectangular nursery tray built specifically for sowing seeds and propagating small cuttings. It is elevated on four short feet to allow excess water to escape underneath, preventing root rot. Design Features Drainage Grid: A regular pattern of 3.5mm holes across the bottom ensures proper water flow. Elevated Base: 5mm feet keep the tray off flat surfaces, allowing air circulation and drainage. Sturdy Walls: 2mm thick perimeter walls provide enough rigidity to move the tray when fully loaded with damp soil.
Wall-Mounted Bedside Floating Shelf
What it's for A sleek floating shelf for beside the bed at about head height, sized for an ornament or a small potted plant. A back plate with four countersunk screw holes fixes it to the wall, and two triangular brackets support the top. The design is symmetrical, so printing two gives a matching pair for each side of the bed. Dimensions Shelf top: 200 × 120 × 12 mm, rounded edges Back plate: 170 mm wide, 6 mm thick, 70 mm tall including the shelf Screw holes: four, 4.5 mm shank with 9 mm countersink, set 80 mm apart, the upper pair just below the shelf Brackets: two, 6 mm thick, at X ±70 mm Print notes Prints with the top face on the bed, with no supports needed. Use wall plugs suited to your wall type and countersunk screws with heads up to 9 mm. Remix ideas Narrow the shelf for tighter spaces. Add a small front lip to keep ornaments from sliding off. Add a cable notch for a bedside lamp.
125mm 8-Rib Filter Wrench
Two-piece water filter wrench sized for 125mm (4.5-inch) housings, featuring an 8-rib engagement ring. Joint: Heavy Z-axis sliding dovetail Fit: 125mm inner diameter with 8 notches Print Volume: Parts separated to fit 180x180mm print beds
Fenstergriff-Halter Block 110x20x30 mm
Block mit 110 x 20 x 30 mm und zwei Aussparungen an der Unterseite zum Einhaken in Fenstergriffe. Die Aussparungen haben unten gerade Wände und oben eine runde Form (Ø25 mm). Die Öffnung ist mit 21 mm etwas schmaler als der Griff, damit dieser einrastet. Maße: 110 x 20 x 30 mm, Kanten 1,5 mm angefast Aussparungen: Ø25 mm rund oben, 21 mm breite gerade Öffnung unten Mittenabstand: 70 mm Durchgehend durch die 20 mm Breite Material: PLA oder PETG, ohne Stützen druckbar
110x80mm Invertible Wall Shelf
A simple, sturdy wall shelf with a subtle rim on the underside, designed so it can be mounted inverted. Features a 110x80mm flat area and integrated reinforcement gussets for rigidity against the wall. Dimensions: 110mm width x 80mm depth. Mounting: Twin countersunk screw holes on the backplate. Features: 3mm retention lip and dual structural gussets.
Need a part that doesn't exist yet?
Start building →