3D-printable workshop tools & shop upgrades
Drill guides, tool racks, sanding blocks, dust-collection adapters — functional shop gear with real dimensions, ready to print. Browse what makers built, or describe the exact tool you need and Printy makes it.
Need one that fits your exact measurements? Start building →
Newest

Detailer's Triptych Vacuum Set
A custom trio of detailing tools designed specifically for the standard 35mm friction-fit wands found on most Karcher wet/dry workshop vacuums. Each piece serves a distinct stage of an automotive deep clean. The set features: The Crevice Tool (Red): Extended and sharply angled to slip between seats and center consoles. The Wide Nozzle (Blue): Flared to 80mm with a shallow scraping edge, ideal for lifting stubborn dirt from floor mats and broad upholstery. The Detailing Spot Nozzle (Green): Narrowly focused into a 16mm tip for intense, localized suction inside cup holders, vents, and door pockets. Designed to print without supports—just drop them on the bed vertically.
Eccentric Cam Twist-Lock Prototype
A three-piece prototype demonstrating an internal cam-based locking mechanism for telescoping poles. The inner tube carries an eccentric spool on its tip; twisting the handle forces the captive cam outward against the walls of the outer tube to lock the extension at any length. Mechanism Notes Offset: The spool is offset by 1.5 mm, which translates to a full lock within roughly a 15 to 20-degree twist. Guide Rail: The outer tube features an internal rail. The cam is slotted to ride this rail (preventing it from turning), while the inner tube has a wide 90-degree channel cut out so it can rotate freely past the rail. Assembly: Slide the inner tube up through the outer tube until the spool clears the top, snap the cam onto the spool sideways via its keyhole slot, and pull the whole assembly back down into the housing.

Acrylic Sliding Channel Clip
This low-profile edge clip is designed to hold a 0.093" (2.4mm) acrylic sheet flush against a flat surface. Rather than fixing the panel in place, the clip features an open track, allowing you to use multiple clips to build a sliding channel. Remix variables: Acrylic Thickness: Currently set for a 2.6mm gap to allow a 0.093" sheet to slide freely without binding. Overlap: 8mm lip reach. Mounting: Uses an M3 socket head screw, featuring a 3mm slotted channel to let you fine-tune the clamping pressure against the panel during install. Ideal for easily removable 3D printer enclosures, sliding doors, or modular dust covers.
Eccentric Cam Twist-Lock Prototype
A three-piece prototype demonstrating an internal cam-based locking mechanism for telescoping poles. The inner tube carries an eccentric spool on its tip; twisting the handle forces the captive cam outward against the walls of the outer tube to lock the extension at any length. Mechanism Notes Offset: The spool is offset by 1.5 mm, which translates to a full lock within roughly a 15 to 20-degree twist. Guide Rail: The outer tube features an internal rail. The cam is slotted to ride this rail (preventing it from turning), while the inner tube has a wide 90-degree channel cut out so it can rotate freely past the rail. Assembly: Slide the inner tube up through the outer tube until the spool clears the top, snap the cam onto the spool sideways via its keyhole slot, and pull the whole assembly back down into the housing.
Nit ring v3.2 (7.4mm)
What it's for A custom two-stage spacer or bushing. The bottom section flares out for a wider footprint, while the top maintains a straight profile. A continuous through-hole runs the entire length, with a shallow counterbore at the base to recess a bolt head or capture a mating pin. Dimensions Total Height: 12.5 mm Tapered Base: 9 mm diameter at the bottom, flaring to 13 mm over a 3 mm height. Straight Collar: 9 mm diameter, 9.5 mm high. Bore: 7 mm clearance hole straight through. Counterbore: 9 mm diameter, recessed 2 mm into the bottom. Print notes Print this sitting flat on its wide base. The counterbore is shallow enough that most standard profiles will bridge it without requiring supports.
Rounded Cylinder Base
A heavy-duty base piece that sits flat without catching on surfaces. The bottom edge is heavily radiused to clear corners and prevent scratching, while the top houses a precise pocket for mounting. Footprint: 65mm diameter x 12mm height Top Pocket: 19mm wide, 5mm deep Bottom Edge: 5mm radius rounding
Gridfinity Double Fiskars Slim 4x2 Dock
A custom Gridfinity-compatible tool tray designed to dock two Fiskars Pro Retractable Utility Knives. The knives drop vertically into precisely angled slots, while a cubby has room for a bunch of 80x18mm utility blades. What it's for Keeps your primary utility knives loaded, upright, and instantly grabbable, with spare blades tucked right underneath. Dimensions Footprint: Standard 4x2 Gridfinity base. Knives: 13-degree rear tilt for easy handle clearance. Blade Cubby: 90x64x27mm internal volume, with a 6mm retaining lip. Remix Ideas Extend the depth to a 4x3 footprint if you want to add slots for marker pens or rulers in front of the blades. Adjust the blade cubby lip height if you use custom-printed blade dispensers instead of the factory packs.
Color Insert For Slim 4x1 Fiskars Knife Dock
precision-fit tool dock insert designed to scream when a tool is missing. By printing it in a high-visibility colour and dropping it into the base of a neutral-coloured dock, an empty slot instantly becomes a visual alert. designed to fit into this dock: https://printytron.com/m/slim-4x1-fiskars-knife-dock-hd9q Features Stencil Cutout Typography: The tool name is cut entirely through the 2mm base plate. Because Black Ops One is naturally stencilled, the islands in the letters won't fall out, and the dock body's colour shines straight through. Drop-In Fit: Sized precisely for the bottom of the Fiskars Utility Knife cavity. Elephant's Foot Compensation: Features a slight 0.4mm bottom bevel to ensure the print presses cleanly into the dock floor without binding on a squished first layer.
Slim 4x1 Fiskars Knife Dock
A highly functional Gridfinity-compatible dock tailored for the Fiskars Pro Retractable Utility Knife (model 770210-1001), now remixed into an ultra-slim 4x1 form factor. Standing the knife securely on its side allows it to drop into tight spaces without eating up valuable pegboard or drawer real estate. Design Features 4x1 Gridfinity Base: Minimises footprint; perfect for slotting into long gaps between wider trays. Vertical Docking: Seats the knife securely on its side while leaving the handle prominent for quick grabs. Scalloped Finger Access: Features a sweeping 60mm side-cutout that leaves a structurally sound 10mm lip above the base plate, granting plenty of clearance for larger hands. Clearance Channel: Incorporates a deeper relief inside the slot so the blade slider won't bind.
1.95" x 0.195" Chamfered Sleeve
A simple sleeve spacer or bushing. Features: Outer Diameter: 1.95 inches Inner Bore: 0.195 inches (through-hole) Overall Height: 2.5 inches Internal chamfers on both ends of the bore to ease insertion. Check your shaft diameter and required clearance before running off a print.

Chamfered Heavy Duty Spacer
A 2.5-inch tall solid cylinder spacer with a 1.5-inch outer diameter and a 0.38-inch inner diameter. The inner hole features 1mm chamfered edges at the top and bottom to guide inserted parts and reduce edge stress. Outer Diameter: 1.5" (38.1 mm) Inner Diameter: 0.38" (9.65 mm) Overall Height: 2.5" (63.5 mm) Edge Treatment: 1mm ID chamfers

Sockenlineal für Schuhgrößen
Ein einfaches Messwerkzeug, um während des Strickens die Fußlänge und Schuhgröße einer Socke zu bestimmen, ohne das Strickstück ständig anprobieren zu müssen. Das Lineal wird direkt in die Spitze geschoben. Die eingravierten Skalen in Zentimetern und EU-Größen nutzen sich nicht ab und gleiten glatt am Garn vorbei. Maße und Parameter Länge: 300 mm Messstrecke. Breite: 50 mm, passend für gängige Sockenspitzen. Stärke: 2,4 mm (steif, aber noch nicht sperrig). Skalen: CM oben, EU-Größen unten, nach außen gerückt für bessere Ablesbarkeit.
Dust Extractor Static Turbine
Nothing stops a project faster than trying to perfectly align a separate impeller core inside a printed housing while the glue dries. This design builds the stator directly into the pipeline — a single solid print where the central shaft is locked to the walls via mid-body struts. The blades are pitched to guide airflow and trimmed completely flush with the adapter's inner taper, so there's no risk of them breaching the outer shell. Dimensions & Setup Total Height: 140 mm Shaft Diameter: 12 mm Blade Setup: 6 angled blades at the 4-inch base, 6 more at the 2-inch top. Mounting: 3 stationary support struts across the transition zone. Printing Note: Built as a single solid part (stator). If used for dust extraction, printing in PETG is recommended to handle the abrasion from chips.

Low Profile Probe Rack
A bulky wall mount that catches on sleeves and knocks things off the bench is exactly what we don't want. Chopping the back plate down to a stubby profile gets the plastic out of the way while keeping the rack mounted firmly against the wall. Fit Details Capacity: 8 scope probes Grip Clearance: 10mm holes Mounting: Swapped to smaller M3 countersunk holes to fit the shorter 12mm back plate
8-Probe Slim Wall Rack
Tired of oscilloscope probes sliding off the bench and getting crushed by heavy gear? This wall-mounted rack gets them up and out of the way. It holds eight probes cleanly, keeping the cables untangled and the tips safe. Dimensions & Details Capacity: 8 slots (15mm diameter cutouts, 5.5mm entry slots) Overall Size: 220mm wide x 53mm deep x 17.5mm high Mounting: Three countersunk screw holes (4.5mm shaft, 7.5mm head) Printing: Prints flat on its base, no supports required. Thinned down to save material and print time.
Brymen BM789 Multimeter Desk Stand
A dedicated desk stand for the Brymen BM789 multimeter. The stand pitches the meter back at 30 degrees from vertical for bench readability. Crucially, the BM789 routes its test leads from the bottom face—so the lower lip and base plate feature a 65mm-wide central clearance channel. The meter sits on the outer shelves of the tray while the leads drop straight through to the desk. Fitment checks Width: Internal clearance is 95mm (BM789 in holster is ~89mm wide). Depth: Internal tray depth is 55mm (BM789 in holster is ~51mm). Jacks: The 65mm U-channel easily clears the standard 4-jack spread. Compatibility: Will fit other meters with bottom jacks provided their holstered footprint is under 95x55mm.
Metal Band Multimeter Stand
A spiky, symmetrical desk stand built for holding a multimeter, styled like an illegible gothic metal band logo. Features jagged thorny branches reaching outward and scalloped batwing support fins. Angled Rest: Leans back at 25 degrees for bench visibility. Cable Clearance: A generous 45mm cutout in the shelf allows test leads to stay plugged in while docked. Flat Base: The entire assembly is sliced flat at the bottom for a stable desk footprint.
QuadraBlock — Mounting Plate
Meet the QuadraBlock. A heavy-duty 16mm thick mounting plate designed to handle robust anchoring. It features four recessed corner screw holes for flush mounting, alongside deep counterbored center bolt channels for heavy-duty structural attachments. A one-millimeter chamfer wraps the outer edge to prevent sharp corners and improve durability. Dimensions Overall: 92mm x 92mm square, 16mm thick Corner Mounting: 4mm through-holes with 8mm diameter recesses (3.5mm deep) Center Mounting: 9.5mm through-holes with 18mm diameter recesses (10mm deep) Features Flush Seating: Precision recesses ensure all hardware sits below the top surface. Reinforced Core: 16mm thickness provides high rigidity for torque-heavy bolt connections. Clean Geometry: Chamfered exterior edges resist chipping and catch less dust.

Furo 3.2mm Rebite Snap-Fit
Rebite de pressão (snap-fit) projetado especificamente para união de chapas finas, otimizado para impressão 3D em PLA. Especificações Críticas Furo de Montagem: 3.20 mm Espessura Útil (Aperto): 5.30 mm Diâmetro da Haste: 3.05 mm Diâmetro da Cabeça: 6.00 mm (com 1.30 mm de espessura) O design foi ajustado para resistir às tensões da impressão FDM com bico de 0.4 mm. O rasgo central desce além da cabeça da trava, dando 3.0 mm completos de alavanca para as abas (que têm 0.65 mm de parede) fletirem sem estourar. A base da cabeça leva um pequeno chanfro de 0.3 mm para compensar o pé de elefante da primeira camada e garantir que ele assente perfeitamente plano contra o painel. A face de retenção tem uma inclinação suave de 80 graus para tracionar levemente o conjunto de 5.40 mm.
Heavy-Duty Weed Puller
A heavy-duty dandelion digger and weed puller. Features a thick, ergonomic handle, a pronounced leverage bump (fulcrum) to easily pry stubborn roots, and a deep V-notch to slice right through taproots. The geometry is deliberately aligned to lay completely flat on its side. This achieves two things: Zero supports: The entire side profile sits directly on the bed. Maximum strength: Levering tools often snap under pressure if printed upright. By laying it sideways, the printing layer lines run the entire length of the shaft, absorbing the levering force seamlessly. Specifications Overall Length: 240mm Thickness: 20mm uniform width Suggested Print Settings: 4+ perimeters and high infill for optimal rigidity.
Scale Room Layout Mockup
Planning a layout with loose paper cutouts that blow away every time someone walks past is useless. This is a rigid, four-walled scale mockup of a specific room, scaled down to 1:24 so you can actually test clearances and sightlines physically. Scale Details Target dimensions: 10ft 10in by 5ft 1.25in (stepped down to 1:24 scale). Cutouts: True-to-size doorway positioned precisely where the real one is. Format: Open roof for easy top-down viewing and placing scaled furniture.

Heavy-Duty Screwdriver Wall Rack
A solid, heavy-duty wall-mountable rack designed to hold five large screwdrivers vertically. Built to maintain a sturdy grip on hefty tool handles while keeping the mounting hardware completely separate from the tool shafts. Features: Accommodates 5 screwdrivers Wide handle cups (28mm) for heavy-duty tools Generous clearance between tool sockets and mounting holes Chamfered front and edges for a clean look Counterbored mounting holes for standard wood screws
M18x2.5 Socket Cap & Nut
An M18 x 30 socket head cap screw with a matching hex nut, designed for direct 3D printing. The bolt features a standard 2.5mm coarse pitch and a 14mm hex drive recess in the head. It prints head-down to avoid overhang issues. Fitment Notes Thread: M18x2.5 (Coarse) Drive: 14mm Allen / Hex Key Nut Wrench Size: 27mm Clearance: 0.2mm on the nut threads for a tighter fit. Ensure your printer's flow rate and dimensional accuracy are well-calibrated, or the threads may bind.

1U Omada Split Rackmount
A 1U split rackmount designed to securely hold a TP-Link Omada ER605 Router and an OC200 Hardware Controller in a standard 19-inch rack. The mount is designed to fit onto most consumer 3D printer beds by splitting exactly down the middle. The two halves securely lock together via three jigsaw joints on the base plate, requiring no glue or external hardware for assembly. Features front cutouts sized precisely for the ER605 and OC200 Internal guide walls hold devices squarely in place Rear stops are dimensioned to position the front faces of the devices exactly flush with the rack plane Base ventilation slots reduce filament use and aid passive cooling
Need a part that doesn't exist yet?
Start building →