3D-printable gifts & personalized pieces
Cake toppers, ornaments, seasonal displays and custom-text pieces made to order. Browse what makers built, or describe the exact gift you need and Printy makes it — right down to the name and date.
Need one that fits your exact measurements? Start building →
Newest
V2_Aşkım Love Letter Photo Frame
Ein winziger Bilderrahmen im Stil einer Liebeskarte: Der Name „Aşkım" thront als erhabene Schrift über dem Rahmen, auf der Rückseite wartet eine versteckte Botschaft samt großem Herz. Außenmaß 52 × 52 × 1,5 mm, Fach für ein 50 × 50 mm Foto Rückwand 0,6 mm, geschlossen Name 4 mm hoch in Arial-ähnlicher Schrift (Liberation Sans) Unterseite: Widmungstext und Herz, 0,25 mm tief graviert (lesbar von hinten)
Mike Wazowski Horns for Shirt
Two horns to sew onto a maternity shirt for a Mike Wazowski costume. A loose horn flops or slides off fabric, so each one has a flat round base with sewing holes to stitch it down. Key numbers Height: about 47 mm each Base: 40 mm round disc, 3 mm thick Six 3.2 mm sewing holes around each base Print: base flat on the bed, no supports needed, cream or white filament
110×70 mm Himalaya School Visitor Pass
Two-body visitor pass for Himalaya Public Sr. Sec. School: a white 110 × 70 × 4 mm plate with 3 mm corner radius, and solid dark-blue raised lettering. Fit and dimensions Plate: 110 × 70 × 4 mm, rounded corners. Letters: 2 mm proud of the plate, flat bottoms seated on the top face (overall height 6 mm). Text: HIMALAYA PUBLIC / SR. SEC. SCHOOL / VISITOR PASS, centred, well inside the 4 mm margin. Check before printing Confirm the text stays within 4 mm of every edge in your slicer. Assign the white and blue bodies to separate filaments. There is no hole or lanyard slot.
Wazowski — Hinged Arms, Viper Horns
Wazowski is a set of two hinged monster arms and two horns, made to sew onto a maternity shirt panel. Each arm splits into an upper arm and a forearm with hand, and the horns are slender, backward-curving thorns in the style of a desert horned viper. Features Upper arm with a single lower hinge plate. The top plate is left off so the forearm can be glued in place. Forearm and hand with three fingers and a thumb, plus a short pin that locates in the hinge hole. Two horns, 60 mm tall, tapering to a fine tip with a slight curve. Round flanges with six sewing holes on each arm and horn. Print notes Print the arms in TPU or another flexible filament so they move with fabric. Glue the forearm knuckle onto the hinge plate with the pin seated in the hole. Proportions are set for scaling, so resize in the slicer to fit.
Slipbar — Snap-On G Cap
Slipbar G Cap is a standalone G-shaped cover that snaps onto the corners of a 68 × 38 × 10 mm rectangular buckle frame. The plate itself is the letter G, stretched to fill the frame's face, with a small clip at each corner. Features G-shaped plate, about 71.6 × 41.6 mm Four corner clips with small inward lips that catch the frame's lower edge Mirrored so the G reads correctly from the front face when printed face-down Print notes Print with the front face on the build plate PETG flexes best for the clips Test-fit the snap and adjust the lip if it is too tight or loose
Yoshi Saddle Shell Backpack Mount
A red Yoshi-style shell dome on a white base plate that straps onto a backpack. What it's for Turns a backpack into a Yoshi costume piece. Webbing passes through four slots in the base plate, so the shell sits on the backpack's outer face. Dimensions Overall: about 214 × 175 × 94 mm, fits a 256 mm bed in one piece Dome wall: about 4 mm, hollow underneath Base plate: 6 mm thick Strap slots: four, each 44 × 7 mm, at X ±60, Y ±32 Remix ideas Add white spots or a ridge band on the dome Widen the slots for thicker webbing Add a foam pad under the base plate
Armoured Oyster Bracelet Mid-Link
A reinforced stand-in for a broken oyster-style solid link, with a crowned top and an R45 concave underside that follows the wrist. The hinge ends are built to take the load. Female end: two Ø5.2 ears around a 5.2 mm gap; male end: one Ø4.6 × 4.4 mm tongue. Ø1.6 pin bores, 35.8 mm pin to pin. Underside pocket stops 11 mm from centre, leaving solid hinge zones. Filleted webs where the ears meet the body. Ream the pin holes to 1.5 mm after printing.
T-Rex Holding LUKE Sign
A standing T-rex on a flat base, gripping a name sign that reads LUKE in raised lettering. Prints as one piece, sign facing front. Remix hooks Name: swap "LUKE" for any short name; keep the sign about 60 mm wide, or widen it for longer names. Font and size: Luckiest Guy at size 12 fills the 60 x 22 mm sign; drop the size if the name grows. Base: 70 x 100 x 3 mm, easy to enlarge or turn into a keychain-sized stand. Colour split: base, dino and sign are separate regions, ready for multicolour prints. Pairs with: a desk shelf, or a row of dinos with different names.
3.2 mm Jump Ring Georgie Letter Links
Seven individual letter links spelling G-e-o-r-g-i-e, made to be joined by metal jump rings into a name bracelet. Fitment Each link is a 14 × 14 mm plate, 3 mm thick, with the letter raised 1.5 mm in Luckiest Guy. A 3.2 mm hole runs front to back through a round tab on each side, so a ring passes through the flat face. Hole centres are 19 mm apart on each link; adjacent links join with one jump ring through facing holes. Check before printing Jump ring wire must be under about 3 mm, or the holes will not take it. Does not fit Rings with wire thicker than 3 mm, or links with a closed clasp-style bail.
46 mm Brooch with 32 mm Pin Bar Slot
A 46 mm round flower brooch with two layers of petals, a domed centre stone and a beaded rim. It is designed for a standard 30 mm pin-back bar glued into the back. Fit check Back groove: 32 × 6.4 × 1.2 mm. Measure your pin bar before printing. It fits bars up to about 30 mm long and 6 mm wide. Does not fit: clutch-style or screw-post backs. It has no hole for either. Print: face up with no supports needed. Use a multi-colour or paint the layers separately. Size: 46 mm across, about 6 mm tall.
Monolithic Grid Advent Calendar
A complete, print-in-place Advent calendar designed specifically to fit on the Bambu Lab A1 Mini (180x180x180 mm build volume). It features exactly 24 sliding drawers arranged in a space-efficient block, numbering from 1 to 24 sequentially. The top two rows contain 8 larger drawers perfect for bigger treats, while the bottom four rows hold 16 smaller drawers. Print-in-Place Design Ready to Slide: The drawers and frame are printed together as a single unit. Tolerances are tuned (0.4 mm on sides and bottom, 1.0 mm on top) so the bridging above each drawer naturally sags without fusing the parts together. Zero Assembly: No separate rails, glue, or snap-fit parts to mess with. Easy Grip: Each drawer features a neat little half-circle finger notch at the top, making them easy to pull open. Printing Tips No Supports: Do not generate supports, as they will fill the internal gaps and fuse the drawers to the frame. Cooling: Ensure your part cooling fan is running high so the bridges above the drawers stay relatively crisp. Material: Standard PLA works perfectly. White gives it a clean, classic winter look.
Happy 40 Birthday Cake Topper
A solid, 3D-printable birthday cake topper reading "HAPPY 40". Designed for clear legibility from across a room, the text uses a heavy Archivo Black font extruded to a sturdy 4mm thickness. The letters are anchored to a continuous horizontal bridge, ensuring the entire piece remains rigid and prints as a single continuous body. A central, tapered 85mm stake extends from the base for secure insertion into a cake. Prints flat as a single solid piece 25mm tall text for high visibility 4mm overall thickness provides structural rigidity 85mm central tapered mounting stake
Lemon Slice Earring Cover
A two-piece clamshell case designed to snap cleanly over a 29mm circular earring. Both halves print face-down and feature the decorative lemon slice pattern on their outer faces. What it's for Transforming a plain hoop or disc earring into a 3D fruit slice without permanent modification. The two halves securely press-fit together, sandwiching the jewelry inside while leaving a notch for the earring hardware to pass through normally. Dimensions Overall size: 36 mm diameter, 6.5 mm total thickness when assembled. Internal pocket: 29.5 mm diameter by 2.5 mm deep, tailored for a 2 mm thick earring. Hardware slot: 4 mm wide notch at the top edge. Assembly Prints as two separate pieces side-by-side, with the decorative faces flat on the bed. Features four alignment pegs that snap the halves together. The symmetrical layout ensures the hardware slots align perfectly when closed.
X26 Prop Holster, 2.21 in Belt, Strap
A prop X26 holster pouch with a belt loop and a separate U-shaped retention strap, sized for a duty belt 2.21 in (56 mm) tall and 0.21 in (5.3 mm) thick. Fit notes Belt slot: 60 mm tall, 7.5 mm thick. It will not fit belts wider than about 58 mm. Pocket: tapers from 70 × 44 mm at the base to 84 × 48 mm at the mouth, 130 mm deep. These are estimated prop dimensions, not measured. Check your prop before printing. Strap: a separate U-shaped piece with keyholes that mate with the two 5 mm studs on the rim. It prints flat and is not attached to the pouch. Not a working Taser holster. Prop use only.
Realtor Anniversary Commemorative Plaque
A custom decorative plaque commemorating a tenth work anniversary for a realtor. The layout features personalized congratulatory text, a decorative scroll motif, and a detailed house icon to mark the occasion. Key details: Solid rectangular base with rounded corners Raised outer border for framing the text Centered typographic layout spanning multiple fonts Stylized house icon and decorative center scroll
Luggage Strap Tag, 5 mm Slot, STEVE
A 90 × 50 × 3 mm luggage tag with a 5 × 22 mm strap slot and the name STEVE raised inside a recessed label panel. Fitment Fits straps up to 5 mm thick through the 22 mm-wide slot. Does not fit wide or double-layer straps, or standard key rings without a loop. Measure the strap thickness before printing; the slot is 5 mm. The lettering stands 0.9 mm proud of the panel floor and sits below the tag's top surface, so it is protected from rubbing.
IN Beads Slip-Knot Spacer
A sleek, miniature 3D-printable cylindrical spacer designed to conceal a sliding knot on an adjustable bracelet. Measuring exactly 14mm in length with a 10mm outer diameter, the body houses a spacious 7mm internal chamber that comfortably fits a 6mm tied knot. Design Notes Precision Fit: The 3mm cord openings on each end feature gently flared inner edges to prevent cord snagging during adjustment. No Supports Needed: The internal chamber geometry bridges cleanly, keeping the pathway perfectly unobstructed. Recessed Branding: The "IN Beads" logo is deeply debossed at 0.4mm into the front face, perfectly scaled for high-resolution resin printing. Surface Ready: The outer rim carries a smooth 0.3mm radius, preparing the part perfectly for a brushed metallic post-processing finish.
Curved Halloween Horn for "Power"
A hollow, gently curved cone horn with an open base, sized for Halloween costumes. Base diameter is 40 mm, height 60 mm, with the tip leaning 25 mm to one side and a 2.5 mm wall. Remix hooks Base diameter (D = 40 mm): widen for a headband mount, narrow for a hairclip or small hat. Bend (25 mm): lower for a straighter horn; higher gives a hook-like sweep, but needs more support when printed upright. Wall (2.5 mm): thin it to save filament, thicken for durability. Height (60 mm): stretch for a taller, more dramatic horn. Pairs with A mirrored copy for a matching left and right set. A headband, a hat, or a printed base ring with a slot for mounting.
Hartvormige fotolijst voor oma
Hartvormige fotolijst ontworpen rondom de standaardafmeting van een 10x15 cm foto. De lijst bevat verhoogde details zoals bloemen, kleine hartjes en de tekst in het Satisfy-lettertype. Omdat reguliere emoji's niet naar gcode vertalen, is het hartje in de tekst vervangen door een massief 3D-element. Constructie en Printen De Sponning: Aan de achterkant zit een uitsparing van exact 104x154 mm. Dit geeft rondom 2 mm speling voor de foto, plus de 3 mm dikke rugplaat. Ondersteuning: Print het hoofdframe plat op zijn rug. Voor de sponning van de foto is in de slicer een beetje "support" (ondersteuning) vereist. Montage: De rugplaat klemt strak in het frame. De losse standaard schuift onder een hoek van 45 graden in de rugplaat. Gebruik eventueel een klein beetje tape of lijm als de frictie van je print niet strak genoeg is.
Kids Fidget Board with Spinner
A fidget board for small hands: a base with a three-lobe spinner and a sliding button in a track. Printed as five separate pieces, so nothing fuses and no supports are needed. Base: 70 × 36 mm with a spinner pocket, a fixed axle and a through slot with an underside recess. Spinner: prints flat, drops over the axle with 0.7 mm clearance per side. Axle cap: glues onto the peg at the top of the axle to hold the spinner on. Slider button: prints flat with the stem pointing up. The stem passes through the slot. Retaining foot: glues onto the stem underneath, inside the recess, so the button slides but cannot lift out. Assemble in this order: spinner, then cap; button stem through the slot, then foot glued on. Use glue suited to the filament, and check that glued parts are fully secure before giving the toy to a young child.
Twin-Chamber Skull Death Whistle
A skull-shaped death whistle with two resonant chambers for a rough, beating scream. Blow into the mouthpiece at the back; air runs along a flat duct, splits on a sharp edge over the window, and sounds both chambers. Remix hooks Duct height (2.4 mm): the main pitch and breathiness control. Try 2.0–3.0 mm. Chamber diameters (20 mm and 12 mm): the gap between them sets how harsh the scream is. Closer sizes give a beat, wider gaps a growl. Chamber height (13 mm): taller means lower pitch. Skull shape: cranium radius is 27 mm, jaw block 34 × 40 × 14 mm. Eye sockets, nose and teeth grooves are separate cuts and easy to restyle. Pairs with: a cord through a drilled lug, or a third chamber behind the first. Overall size is roughly 54 × 78 × 49 mm including the 16 mm mouthpiece. Print upright; the window opens through the crown.
Starfleet Communicator Halloween Prop
A handheld communicator prop in the spirit of classic Star Trek, sized to carry or clip to a costume belt. It is a 90 × 36 × 12 mm slab with rounded corners, a slotted speaker grille, a round dial and a raised gold-style delta emblem. Remix hooks Body size: 90 × 36 × 12 mm. Scale length for a chunkier prop or shrink it for a pocket version. Grille slots: nine slots at 4 mm spacing. Change the count or width for a different look. Emblem: the delta is a simple 4-point polygon. Swap in a different insignia or text. Dial: 10 mm round knob. Make it a button, or add a hole for a small LED. Pairs with: a belt clip, a keyring loop on the back, or a hinged lid to make it a true flip communicator. Printing: print the parts in silver, gold and blue, or paint after printing.
Bracelet Octobre Rose 78mm
Un bracelet jonc simple et élégant, gravé du texte "OCTOBRE ROSE" en creux pour marquer l'événement sans nécessiter d'impression multicolore. Diamètre intérieur : 78 mm (ajusté pour un enfilage confortable) Épaisseur de paroi : 3 mm Hauteur : 12 mm Gravure : Découpée dans la paroi extérieure Impression : Conçu pour s'imprimer à plat sans aucun support
Elderstab 1.0
What it's for A two-piece print of the iconic Elder Wand, split cleverly right after the third handle knob to hide the seam. Dimensions Total length: ~250 mm Handle: ~102 mm, featuring a 10.4 mm x 3.2 mm recess for a ring magnet and a 35 mm deep secret compartment (6.5 mm diameter) hidden behind it. Tip: ~150 mm, with a 10.4 mm x 3.8 mm recess for a flat magnet (includes extra depth for felt padding). Assembly Glue a 10x3 mm ring magnet into the handle and a 10x2 mm flat magnet into the tip. Add a thin piece of felt between them for a softer snap. The secret compartment can hold a tightly rolled message.
Need a part that doesn't exist yet?
Start building →