3D-printable storage & organizers
Boxes, wallets, dispensers, holders and carriers sized for real contents. Browse what makers built, or describe the exact organizer you need and Printy makes it.
Need one that fits your exact measurements? Start building →
Newest
12mm Bore 8-Slot Screwdriver Rack
An 8-position wall rack designed around a straight 12mm bore to capture standard screwdriver shafts. The top of each slot flares into a 30mm funnel, guiding tools into place without precise alignment above the workbench. Capacity: Holds eight screwdrivers with shaft diameters up to 11.5mm. Handle Clearance: 32mm center-to-center spacing. Accommodates standard acetate or rubber grips, but will crowd or reject over-molded handles larger than 30mm. Mounting Interface: Three recessed bores cut for standard #8 countersunk screws. Critical Dimension: Verify the maximum diameter of the tool handles before printing to ensure they will not interfere across the 32mm spacing.
GridLock — Split Open Drawer Frame
GridLock is a custom-fit drawer divider system completely stripped down to its essentials. Sized specifically to frame out compartments without wasting material on a floor, this open-grid organizer drops directly into a drawer, letting the existing liner or wood bottom show through. The frame has been split into four cleanly cut sections to allow printing a large 13.5-inch wide organizer on standard 220mm square print plates. Dimensions Total Assembled Footprint: 342.9 mm wide × 228.6 mm deep (13.5" × 9") Height: 25.4 mm (1") Maximum Piece Size: 171.5 mm × 114.3 mm (fits comfortably on an Ender 3 or Prusa MK series) Layout One full-width front compartment (3.5" deep). Two back compartments (one exactly 3.5" wide, the other filling the remaining space). No bottom—sits flush on your drawer base. Assembly Notes The four quadrants print completely flat without supports. Because the perimeter walls are thin to maximize storage space, they use straight flush cuts rather than bulky joints. Just add a drop of superglue (CA glue) to the seams, press them together on a flat surface, and you're good to go.
Aufsteck-Schraubklemme mit Haken
Eine umstrukturierte Klemmhalterung, die sich als offenes U-Profil direkt über ein 15 x 15 mm Vierkantrohr stecken lässt. Die Fixierung erfolgt durch eine gedruckte M10-Druckschraube auf der Rückseite, die das Rohr fest gegen die Vorderwand presst. Auf der Frontseite sitzt ein massiver Haken. Anpassungsmöglichkeiten für Remixes Dieses Modell ist so ausgelegt, dass die grundlegenden Klemm-Mechanismen leicht für andere Einsatzzwecke skaliert werden können: Stangenmaß: Der innere Ausschnitt hat aktuell 15,6 mm Breite für etwas Spiel auf 15 mm Stangen. Wer größere Rohre nutzt, kann den Hauptkörper entsprechend verbreitern. Haken-Geometrie: Der Ausleger ragt 12 mm nach vorne, die Spitze zieht 16 mm nach oben. Das lässt sich gut durch flache Halterungen oder Ösen ersetzen. Gewinde: Das M10x2 Gewinde hat im Gehäuse 10,6 mm Durchmesser (intern). Für mehr Klemmkraft auf glatten Metallrohren kann die Schraube gegen eine Standard-Metallschraube mit Gummipad getauscht werden.
90mm Meshing Token Tray
A modular hexagonal tray and lid set for organizing board game tokens and dice on the table. The trays measure roughly 78mm flat-to-flat and 90mm point-to-point. Fitment details Mating surfaces: Vertical interlocking uses a standard 3mm stacking boss with 0.5mm radial clearance to ensure parts don't fuse or stick. Side meshing: The exterior tray walls feature vertical ribbing spaced at 4mm to interlock with neighbouring trays, keeping clusters tight. Inner dimensions: The interior floor features a deep 6mm slope so chits and small tokens will slide cleanly into your hand instead of trapping in the sharp hexagonal corners. Clearances: The lid shares the stacking boss but drops the outer ribbing for easier grip and clearance.
Labelled AA Battery Sorting Tray
Keep fresh batteries separate from the ones waiting for recycling. This shelf organizer holds 24 AA batteries lying flat on their sides, divided into two distinct sections to eliminate guesswork. The wide central trenches allow you to get a finger underneath the batteries to pop them out without prying. Features: Holds 24 standard AA batteries horizontally (12 per side). Dedicated "NEW" and "DEAD" sections with embossed front labels. Sized with 15mm slots for easy drop-in of 14.5mm diameter cells. Continuous finger grooves running the length of each compartment for quick removal. Low profile layout designed for shelf storage.
Drop-In Double Fiskars Knife Dock w blade storage
A custom Gridfinity-compatible tool tray designed to dock the Fiskars Pro Retractable Utility Knife (model 770210-1001). The heavy-duty aesthetic of the Fiskars knife calls for a simple, rugged docking station. Built on a standard 4x2 unit footprint, this tray swallows the knife whole while leaving generous finger grabs to pop it out fast when you're mid-project. Design Features 4x2 Gridfinity Footprint: Drops seamlessly into standard 42mm grid baseplates. Tapered Base Profiles: Easy alignment and standard Gridfinity locking dimensions. Ample Finger Clearance: Scalloped sides mean no digging around to retrieve your blade. Slider Channel: An extra-deep central groove ensures the blade slider button doesn't bottom out.
basic Drop-In Fiskars Dock
A custom Gridfinity-compatible tool tray designed to dock the Fiskars Pro Retractable Utility Knife (model 770210-1001). The heavy-duty aesthetic of the Fiskars knife calls for a simple, rugged docking station. Built on a standard 4x2 unit footprint, this tray swallows the knife whole while leaving generous finger grabs to pop it out fast when you're mid-project. Design Features 4x2 Gridfinity Footprint: Drops seamlessly into standard 42mm grid baseplates. Tapered Base Profiles: Easy alignment and standard Gridfinity locking dimensions. Ample Finger Clearance: Scalloped sides mean no digging around to retrieve your blade. Slider Channel: An extra-deep central groove ensures the blade slider button doesn't bottom out.
Creature Comforts — Resource Tray
A custom flush-fit resource tray for Creature Comforts, designed to replace baggies and keep tokens organized on the table. The 3x3 grid perfectly fits all 9 distinct resource types with room to spare, and the compartments feature scooped bottoms so tokens slide out easily with a fingertip. The lid prints flat, drops in with a loose 0.5mm clearance, and includes a finger hole to easily pop it open. Dimensions Overall Footprint: 204 mm × 108 mm × 23 mm (fully assembled) Compartments: 9 bays, 65 mm × 33 mm × 19 mm deep Clearance: 0.5 mm drop-in tolerance for the lid Print notes The lid is already oriented upside down to print flat without supports. The debossed text on the first layer is mirrored in the file so it reads correctly when you flip it over to cap the tray.
Botany Coin Tray and Lid
The worst thing a coin tray can do is let the coins escape sideways into the game box. The outer walls on this tray are completely sealed—the central finger scoop stops before it breaches the edge, trapping the coins safely inside. The labels have been moved down into the floor of the troughs where they can't be misread or cut off. It includes a dedicated slip-cover lid that drops securely onto a stepped lip, designed perfectly for translucent filament. Fitment Details Footprint: 120 × 75 mm base. When closed, the entire assembly is exactly 20 mm tall. Lid Clearance: 0.25 mm gap around the lip for a smooth slip-fit that won't stick. Capacities: Built specifically for Botany's 20mm ($1), 22mm ($3), and 25mm ($5) coins, easily accommodating their full stack depths with room to spare.
Offset Cart Spacer Hook
A heavy-duty mounting hook designed to jump over a cart's top lip and drop down flush against the main side wall. This model includes a spacer brace that sits dead-center behind the hook's lower curve, squaring the load firmly against the side of the cart so it stays plumb under heavy weight. The entire bottom corner is filled solid to prevent flexing at the joint. Remix Dimensions Top Clearance: 22.5mm width for the top cart edge. Lip Jump: Steps out 20mm to clear the side lip. Spacer Clearance: Drops exactly 40mm before the spacer starts pushing back against the cart. Thickness: 12mm thick continuous walls printed flat for extreme layer-adhesion strength. Hook Loop: 40mm inner diameter open-top hook.
Threaded Dual Incense Cases
Slip-fit caps always pop open exactly when you drop the case on the floor, scattering thin brittle sticks everywhere. I swapped the friction fit for a short threaded section — just three coarse turns so it secures fast but doesn't take all day to unscrew. Sizing and Fit Short Case: Fits standard 5.25" (133mm) sticks with a couple of millimetres to spare. Long Case: Fits 8.75" (222mm) sticks. Threads: 3mm pitch, 9mm length. Prints fine without supports, but don't over-tighten on the first test fit until the threads wear in.

Wall-Mounted Display Shelf
A sturdy wall-mounted shelf featuring a J-profile design with open sides. Built specifically to support moderate loads up to 2 kg, it includes a generous structural fillet at the rear corner and three countersunk mounting points to distribute weight evenly against the wall. A pronounced front lip keeps displayed items securely in place. Dimensions Overall Width: 240 mm Overall Depth: 80 mm Back Wall Height: 60 mm Front Rim Height: 30 mm Material Thickness: 6 mm Print Notes Prints flat in its natural orientation (bottom surface on the build plate). The integrated countersunk holes are designed to be printed horizontally; they will bridge correctly on most standard FDM profiles without requiring internal supports. Recommended to use at least 3 perimeters (walls) for structural strength. Assembly Mounts directly to a flat surface using three standard flathead or countersunk screws (up to 4.5 mm thread diameter, 9 mm head). Suitable wall anchors are recommended based on the mounting surface to achieve the full 2 kg load capacity.

Split 1U Smart Home Tray
A three-piece split 1U rackmount designed specifically to fit on smaller printers (under 180mm cubed volume). It supports an Adtran 632 ONT and a Home Assistant Yellow side-by-side, while leaving the third tray configured as a 6-port keystone patch panel. Remixing the Rack Space The base design features locking dovetails and bolted structural flanges that securely bridge the three pieces across a standard 19-inch rack. Keystone Spacing: The 6-port patch panel uses standard 14.8 x 16.2 mm cutouts. The wall directly behind them is thinned to 1.5mm so standard keystone clips engage properly without stressing the jacks. Split Points: The joints occur at X = -80 and X = +80. Adjusting these values lets you shift the proportions of the left, centre, and right trays depending on what device combination you want to mount next. Hardware Required: The mating flanges use four M3x16 bolts and matching M3 nuts to pull the dovetail seams tight and handle horizontal shear.

1U Faceplate Tray for Adtran & Yellow
A split 1U rack tray designed to mount an Adtran 632 and a Home Assistant Yellow side-by-side, featuring a full-height 1U front faceplate with custom cutouts so the ports remain visible and accessible. The two halves join in the middle with a dovetail-style jigsaw joint (0.25mm clearance) so it can be printed on standard beds without hardware. Remixing and Adjustments This tray is built to be tweaked depending on the exact dimensions of your enclosures. Adtran Cutout: Sized at 136.5mm wide by 37mm tall. HA Yellow Cutout: Sized at 122mm wide by 33mm tall. Pockets: The internal fences give the devices 1-2mm of breathing room so they slide in smoothly behind the plate. Adjust the pocket blocks if your particular enclosures are bulkier. Joint Tolerance: The 0.25mm puzzle clearance prints nicely on a tuned FDM machine, but can be pushed to 0.15mm if you want a permanent friction fit.
Cylindrical Snap-Fit Container
A sturdy, minimalist cylindrical container with a flush snap-fit lid. Designed to hold small components, screws, or bits, keeping them securely enclosed. Features Overall Dimensions: 50mm outer diameter, 20mm internal depth. Snap-Fit Mechanism: Features a continuous locking ridge and corresponding groove that engages firmly with a satisfying click. Flush Design: The lid sits completely flush with the outside walls when closed. Print-Ready: The lid is provided in an upside-down orientation, allowing both pieces to print cleanly without any supports.

200mm 3-Compartment Box Base
The base section of a 200mm square storage box equipped with three equal front-to-back compartments. Isolated for direct printing on 220x220mm beds like the Creality K1C. What it fits Sorting and protecting mid-sized tools, hardware, or craft supplies. Mates with the matching 205mm drop-on lid. Dimensions to check Base outer: 200 x 200 x 50 mm Compartments: Three slots, each 64 x 196 x 48 mm internally Wall thickness: 2 mm universally

E-Tray — Bedside Catchall
A low-profile nightstand catchall designed specifically for holding earrings or rings overnight. Features Gentle Profile: Rounded internal and external corners make it easy to sweep small jewelry out. Shallow Walls: At just 12mm tall, it stays out of the way on a crowded bedside table. Monogram Base: Features a recessed 'E' in the center of the floor, using an elegant serif typeface.
Closet Hanger Shelf
A full-scale dimensional model of a standard closet shelf and rod assembly. The shelf sits above with integrated support brackets dropping down to hold the hanging rod securely. Designed at a 1:1 scale to the requested dimensions, it includes: 4-foot (1219mm) overall width 16-inch (406mm) depth with a 1.5-inch (38mm) thick main shelf 1.25-inch diameter hanging rod dropped 75mm below the shelf Three integrated support brackets positioned at the ends and center

Soporte Behringer JT-4000 Micro
Soporte a medida para el sintetizador Behringer JT-4000 Micro, diseñado para fijarse directamente al tubo de un pie de micrófono estándar (20 mm). Fijación: Abrazadera con cierre por tornillo y tuerca M5. Base: Patrón hexagonal integrado para reducir el tiempo de impresión y consumo de material. Estructura: Brazo de soporte corto y macizo para máxima rigidez. Conectividad: Abertura trasera que deja libres los puertos y el paso de cables.

Utilitarian Flush Storage Tube
This monolithic flush-fit cylinder is built to securely house a 38x110mm object. Designed with a seamless exterior, the cap integrates a deeply cut coarse thread that bites firmly and closes flush with the main body walls. The top features a dedicated multi-part text inlay, arranged in an arc, ready for a multi-material print or a precise press-fit assembly. Design Details Clearances: 40.5mm internal diameter with a 112mm depth ensures no binding. Mechanism: Coarse 4mm pitch threads with 0.8mm diametrical clearance. Grip: 12 vertical flutes cut into the cap for torque. Inlay: Text elements are separated into their own part for dual-color extrusion.

Utilitarian Flush Storage Tube
This monolithic flush-fit cylinder is built to securely house a 38x110mm object. Designed with a seamless exterior, the cap integrates a deeply cut coarse thread that bites firmly and closes flush with the main body walls. The top features a dedicated multi-part text inlay, arranged in an arc, ready for a multi-material print or a precise press-fit assembly. Design Details Clearances: 40.5mm internal diameter with a 112mm depth ensures no binding. Mechanism: Coarse 4mm pitch threads with 0.8mm diametrical clearance. Grip: 12 vertical flutes cut into the cap for torque. Inlay: Text elements are separated into their own part for dual-color extrusion.

Utilitarian Flush Storage Tube
This monolithic flush-fit cylinder is built to securely house a 38x110mm object. Designed with a seamless exterior, the cap integrates a deeply cut coarse thread that bites firmly and closes flush with the main body walls. The top features a dedicated multi-part text inlay, arranged in an arc, ready for a multi-material print or a precise press-fit assembly. Design Details Clearances: 40.5mm internal diameter with a 112mm depth ensures no binding. Mechanism: Coarse 4mm pitch threads with 0.8mm diametrical clearance. Grip: 12 vertical flutes cut into the cap for torque. Inlay: Text elements are separated into their own part for dual-color extrusion.

Utilitarian Flush Storage Tube
This monolithic flush-fit cylinder is built to securely house a 38x110mm object. Designed with a seamless exterior, the cap integrates a deeply cut coarse thread that bites firmly and closes flush with the main body walls. The top features a dedicated multi-part text inlay, arranged in an arc, ready for a multi-material print or a precise press-fit assembly. Design Details Clearances: 40.5mm internal diameter with a 112mm depth ensures no binding. Mechanism: Coarse 4mm pitch threads with 0.8mm diametrical clearance. Grip: 12 vertical flutes cut into the cap for torque. Inlay: Text elements are separated into their own part for dual-color extrusion.
Need a part that doesn't exist yet?
Start building →