3D-printable storage & organizers
Boxes, wallets, dispensers, holders and carriers sized for real contents. Browse what makers built, or describe the exact organizer you need and Printy makes it.
Need one that fits your exact measurements? Start building →
Newest
HDX Tote Rack Bracket
A heavy-duty 90-degree corner bracket for 2x4 lumber frames, designed specifically to cradle the corners of HDX 27-gallon storage totes. 2-way 90-degree internal butt joint for standard 2x4 lumber Staggered 5.5 mm screw holes to prevent fastener collision Integrated 2-inch solid outer lip keeps totes from sliding off the frame Thickened outer corner pillar handles heavy vertical loads
Cruzer Blade Sliding Enclosure
A thick-walled, two-part protective enclosure dimensioned specifically for the SanDisk Cruzer Blade. The assembly consists of a main retaining shell and a sliding captive lid. Fitment: Internal cavity measures 42.3 x 18.4 x 8.0 mm (allowing 0.5 mm clearance around the drive). Retention: Dual 0.4 mm internal Z-axis ribs provide friction fit against the drive housing. A solid rear wall prevents push-through. Mechanism: The left-side lid operates on dual 1.5 mm Y-axis rail grooves, featuring spherical detents at both ends of travel for locked open and closed states. Construction: 2.5 mm exterior walls in all directions for rigid PETG FDM printing. The top face includes a 1 mm recess for labelling and a subtracted diagonal chevron pattern.
A5 Rectangular Sensory Tray
A5-sized portrait sensory tray designed with a shallow well for sand, salt, or sugar, and an integrated top slot for holding flashcards or scrapers. Footprint: 148 mm × 210 mm (A5) Well Depth: 4 mm (shifted slightly down to accommodate the card slot) Card Slot: 118 mm wide × 2.2 mm deep, with rounded ends to prevent catching Total Height: 7 mm
Miniature Desktop Luggage Briefcase
An evocative desktop miniature featuring a sturdy print-in-place knuckle hinge, twin corner snap latches, and a pivoting luggage-style carry handle. Fully interlocking structural teeth let it stand securely on its edge. Features Interlocking Hinge & Legs: Offset legs nest perfectly within the hinges when opened flat, clearing each other seamlessly. Twin Snap Latches: Dedicated corner closures are pushed wide to keep the folding handle completely clear of snags. Folding Handle: Integrated pivot pins secure the main handle straight to the top shell. Print-in-Place Ready: Set up as a flat, single-piece assembly to reduce support needs and ensure perfectly aligned mechanics right off the bed.
Brutalist Litter Scoop Sconce
A monolithic, heavy-duty sconce designed to elevate a litter scoop off the floor and out of the box. Rising from a sheer vertical spine, an extended retention hook holds the handle firmly in place, while a sweeping, brutalist deflector chute at the base catches stray clumps and funnels them cleanly back into the tray. The stark geometry ensures nothing collects where it shouldn't. Mounting & Fitment: Wall Clearance: The hook stands 40mm proud of the wall, providing ample room for thick or angled handles. Retention Pin: A 30mm vertical pin with a top catch lip secures the scoop against accidental bumps. Keyhole Mounts: Dual keyholes spaced along the 220mm spine ensure a flush, rigid mount that won't pivot. Deflector Chute: An angled 90mm-wide lower pan directs dry debris and dust downward rather than letting it pool on the floor.
GridLock — Small Drop-In Bins
A set of three drop-in utility bins tailored to fit the smallest full compartment (the 3.5" × 5.1" back-right section) of the open frame system. They share a common footprint but offer different internal layouts for organizing small hardware or desk sundries. Variants Included Open Bin: A single large cavity for maximum storage. Split Bin: Divided neatly in half for sorting smaller items. Coin Scoop: Features a smoothly swept floor across its length, allowing you to easily slide out coins or tiny parts without them getting trapped in a corner. Dimensions Outer Footprint: 88.5 mm × 130.5 mm Height: 38 mm (designed to sit flush just below a 40 mm frame) Clearance: Sized 0.4 mm smaller than the slot for a comfortable drop-in fit
Snap-On Double Bar Shelf
What it's for A wide, flat shelf designed to snap perfectly over a pair of parallel 15mm bars. Instead of resting loosely, the underside features six discrete snap-clips (three per bar) with a slightly pinched opening, allowing it to firmly grip the rails and resist sliding or tipping. Dimensions Overall Size: 220 mm wide × 280 mm deep. Bar Spacing: Fits bars spaced 210 mm apart from the very front edge of the front bar to the very back edge of the back bar. Bar Fit: 15.5 mm cavity with a 14.2 mm snap opening, tuned for standard 15 mm rods. Print notes The shelf is modeled "upside down." Print it flat on its top surface; the snap clips will point upwards and print cleanly without supports. PETG is highly recommended to give the clips the necessary flex to snap onto the bars without shattering.
Massives ESP32 Sensor-Gehäuse
What it's for Ein massives, komplett schraubenloses Gehäuse-System für ESP32-Projekte. Alle Komponenten werden in maßgefertigte Schienen eingeschoben. Der ESP32 rastet im Unterteil ein, das OLED-Display und der Lichtsensor finden im Deckel Platz. Dimensions Außenmaße: 200 × 140 × 70 mm Wandstärke: 3 mm ESP32-Schienen: Passend für 55,3 × 28,0 mm (DevKitC) OLED-Schienen: Passend für 27,3 × 27,3 mm (bis 11 mm Tiefe) VEML7700-Schienen: Passend für 17,7 mm Breite Assembly Beide Teile (Basis und Deckel) werden separat auf dem Druckbett platziert. Der Deckel wird auf dem Kopf liegend gedruckt, um Support für die Deckeloberfläche zu vermeiden. Die Komponenten werden einfach in die Schienen auf der Innenseite eingeschoben, danach wird der Deckel durch die Passkante auf die Basis gedrückt.
Basketball Hair Band & Key Stand
What it's for A desktop organizer that combines hair band storage with a key tray. Features an oversized basketball finial designed to stretch elastics slightly so they won't slip off, a central post for stacking, and a wide dished base engraved with court lines to catch keys, loose change, or lip balm. Dimensions Overall height: ~158 mm Base tray diameter: 160 mm Tray depth: 12 mm Storage post diameter: 32 mm Basketball finial: 55 mm diameter Print notes No supports required. The basketball grooves are modeled to trace the surface and keep the sphere as one solid piece. Print in standard PLA or PETG. The court line engravings on the base tray floor will show up best if printed with a slightly contrasting color swap on the top base layers.
Oghom Steamer Cradle
A vertical cradle sized for the Oghom GH02/GH03 steamer, featuring a large side cutout to accommodate the handle. Internal diameter: 76mm Cup depth: 72mm Mounting: Flat backplate, ready for double-sided tape or your own custom mounting remixes.
Modular Rack Mount System
A modular organizing system designed to bridge a 19-inch rack using standard M8 threaded rods. Drop-in slices let you swap and position devices without taking the rails apart. Upright Slots: Vertical compartments tailored for MacBooks, Mac Minis, and standard routers. Showcase Shelves: Tilted, open-front bays with a retaining ridge and central cable channel for displaying small hubs like a Raspberry Pi, Hue Bridge, or Homey. Drop-In Fit: Each module features open-bottom slots, dropping securely over the support rods without requiring complete disassembly.
200mm Hinged Enclosure Case
What it's for A heavy-duty mounting enclosure that now features an integrated hinge system and a reliable snap-fit latch, replacing the standard friction-fit lid. Designed to house circuit boards, sensors, or bulky wiring, with a secure close that remains easy to access for maintenance. Dimensions Overall footprint: 200 mm × 200 mm Internal depth: 50 mm (plus clearance inside the lid lip) Mounting: Four 5 mm screw holes spaced 30 mm in from the corners Hardware: The hinge uses a standard 3.5 mm pin channel (can be fitted with raw filament or a metal rod) Assembly Both pieces print flat on the build plate. Once printed, insert a piece of 1.75 mm filament, a stiff wire, or an M3 bolt through the hinge knuckles to secure the lid to the body. The latch requires no extra hardware—it operates via intentional plastic flex.
C and 9V Storage Adapters
Drops directly into standard C-cell and 9V battery slots. Adapts the bore to hold a single CR2 cell securely for storage purposes only. Does not include electrical contacts. Fitment Notes C-Cell Profile: 26.2mm outer diameter. 9V Profile: 26.5mm x 17.5mm footprint. CR2 Bore: 16.2mm diameter, 15mm depth. This leaves approximately 12mm of a standard CR2 battery exposed for easy retrieval. Clearance Check: The 9V adapter relies on a 0.65mm side wall around the bore. Ensure your printer's extrusion multiplier is calibrated for thin walls.
PurrFeed — Cat Food Dispenser
Meet PurrFeed — a clean, wall-mounted gravity dispenser designed specifically for 3oz (85g) cat food pate tins, such as Kirkland Signature or Fancy Feast. Load the cans in from the top, and pull them out one by one from the bottom chute. The vertical design takes up zero counter space, and a front viewing channel lets you see exactly how many portions are left before it's time to restock. Features Gravity Feed System: Holds roughly 6 cans at a time; grab the bottom one and the stack cleanly drops down. Tactile Retention Bump: A tiny raised lip at the floor of the extraction window keeps the bottom can securely seated until you lift and pull it out. Recessed Mounting: Three countersunk wall-mounting holes are located down the spine. The screw heads recess fully into the plastic so they won't scratch the cans as they slide past. Sight Window: The 26mm wide front channel gives you a clear view of your supply and doubles as a thumb slot for sliding cans out. Dimensions Overall Footprint: 76mm wide × 76mm deep × 250mm tall. Internal Track: 70mm internal diameter (fits standard 65–66mm pate tins with enough clearance to prevent binding). Extraction Chute: 68mm wide × 42mm tall.
Over-Board Marker Holster
A heavy-duty saddle bracket designed to hang over a standard 19.5mm whiteboard. The main U-shape slips over the board's top edge without fasteners, keeping the front face flush and out of the way. Features a single solid front extension bored out to house one standard 12mm dry erase marker vertically. Slip-fit saddle: Fits 19.5mm thick boards Marker drop: 12.5mm hole for clearance Thick walls: 5mm structural thickness for rigidity Flush construction: Fully merged geometry without seams
Slant-Mount Storage Basket
This basket is designed to clip into a 72x45mm angled opening. The body includes a chamfered bottom corner that perfectly matches a 45-degree mounting plane, allowing the basket to sit level despite the angled interface. Angled Mount: Integrates seamlessly with 45-degree surfaces. Snap-fit Boss: Features flex slots that allow it to compress and securely click into place. Level Base: Maintains a flat interior and flat bottom resting point despite the angled mount.
5-Tier SNES Cartridge Display
A stepped, five-tier display stand designed to hold retro game cartridges upright. The staggered arrangement fans out the cartridges to keep front labels visible without stacking, providing a structured alternative to bulk box storage. Capacity: Five slots configured in a stepped vertical arrangement. Fitment: 20.5mm slot width accommodates standard SNES cartridges with operational clearance. Orientation: 10-degree rearward lean maximizes label readability. Structure: Relieved underside bridge minimizes material usage while maintaining base stability.
Fairy-Tale Flat-Print Tree Organizer
This flat-pack, two-piece organizer channels a storybook woodland silhouette while keeping print times fast and failures low. The tree geometry is laid completely flat on the print bed, dodging the need for support material entirely. Once the plate is finished, it slots vertically into the heavy river-stone base to stand upright, offering nineteen upward-angled pegs to hold small items. Print and Assembly Notes No Supports Required: Both the tree profile and the upward-facing mushroom hooks are designed to clear overhang limits naturally. Sturdy Assembly: A deep mortise in the base block holds the flat-printed trunk firmly in place. Utility: Ideal for hanging rings, light necklaces, keychains, and hair ties.
14-Compartment AM/PM Pill Organizer
A seven-day medication organization tray featuring 14 separate compartments for AM and PM dosing. The base tray accommodates individual friction-fit lids embossed with day-of-the-week initials and corresponding sun or moon indicators to separate morning and evening tablets. Compartment Volume: 25x25x15mm interior capacity per slot. Lid Fitment: Friction-fit covers with a 0.3mm clearance flange. Labelling: Embossed text and iconography for tactile identification. Format: Lids and base separated for flat build-plate orientation.
Splice — Magnetic Hard Case
A rugged, two-piece protective case engineered to house bulky, wraparound eyewear. The two halves print flat and assemble via a robust mechanical hinge, securing shut with discrete magnetic closures. Features Filament Hinge: Designed to accept a length of standard 1.75mm filament as the pivot pin, producing a perfectly tight, metal-free joint. Magnetic Closure: Four dedicated pockets in the front corners accept standard 6×2mm round magnets for a satisfying, hardware-free snap. Dust Lip: The base features an extruded inner ring that mates seamlessly with a corresponding channel in the lid, ensuring precise alignment and keeping debris out. Dimensions Exterior: 165 × 75 × 60 mm (closed) Internal Clearance: 159 × 69 × 54 mm Walls: 3 mm solid perimeter Assembly Notes Print both halves flat on the bed. Once complete, insert the magnets into their corresponding pockets (a drop of CA glue is recommended), align the back knuckles, and thread a piece of 1.75mm filament straight through the hinge line. Snip the excess filament flush.
SG2016P Switch Rack Ears
Desktop switches left dangling by their patch cables or sliding around on top of rack gear are a preventable mess. These custom rack ears bolt right into the side of a TP-Link SG2016P, bridging the gap to a standard 19-inch server rack so it actually stays put. Fit and Fabrication Span: Bridges an 89.5mm gap per side (assumes a 286mm wide switch). Side Mounting: Features three generous slots rather than fixed holes, accommodating variations in where TP-Link drills their chassis. Uses standard M3 or M4 screws. Rack Mounting: Standard 1U slotted holes (31.75mm center-to-center). Printing: Both ears lay flat on their front face. Zero supports required. Print in PETG or ABS if your rack runs hot, though standard PLA is structurally fine for a switch this light.
5.5mm Wire Sign Hanger for string wine racks
En hängare med krok för en 5,5 mm tjock metallstav. Nedre delen har en integrerad klämma (slits) för att fästa ett papper eller en skylt framför staven. Passform: Snäpper över en 5,5 mm stav med greppassning. Klämma: 1 mm bred slits med inbyggda knölar för att låsa fast papperet. Införing: V-formad botten inuti slitsen hindrar papperskanten från att knöla sig. Tjocklek: 5 mm extruderad profil.
Fiskars Dock Indicator Inserts
A pair of 2mm thick inserts specifically designed to press-fit into the bottom of the Fiskars Pro dock pockets. https://printytron.com/m/gridfinity-double-fiskars-slim-4x2-dock-cje9 Printed in a contrasting colour, they act as a visual alarm — the bright base is hidden when your knife is docked, but immediately visible when someone "borrows" it. What it's for Visual tool tracking. Keeps your primary utility knives accounted for. Dimensions Thickness: 2mm flat plates. Profile: Matches the 13-degree tilted clipping of the original dock pockets perfectly. Print notes Print flat on the bed. No supports required. They are exact-fit by design, so you may need a firm press to seat them completely depending on your printer's tolerances.
Monolithic Helmet Hook
A robust, monolithic wall hook designed specifically for the bulk and straps of bicycle helmets. The sweeping, angled arm reaches out far enough to clear the wall, terminating in a rounded lip that won't dig into foam liners or fray fabric straps. Built to print cleanly standing up, the overhang angles are steep enough to self-support on most FDM machines. Mounting Details Backplate: 120mm tall by 40mm wide, distributing the load. Hardware: Two standard 5mm countersunk screw holes. Clearance: The upper screw hole is positioned well above the hook's lip to ensure a screwdriver can reach it straight-on without interference.
Need a part that doesn't exist yet?
Start building →