3D Model Gallery
Every one of these started as a sentence — real dimensions, real holes, print-ready STL. Remix any of them, or describe the part you need and Printy builds it. Start building →
Newest
46 mm Brooch with 32 mm Pin Bar Slot
A 46 mm round flower brooch with two layers of petals, a domed centre stone and a beaded rim. It is designed for a standard 30 mm pin-back bar glued into the back. Fit check Back groove: 32 × 6.4 × 1.2 mm. Measure your pin bar before printing. It fits bars up to about 30 mm long and 6 mm wide. Does not fit: clutch-style or screw-post backs. It has no hole for either. Print: face up with no supports needed. Use a multi-colour or paint the layers separately. Size: 46 mm across, about 6 mm tall.
Select Mini Pi Zero Case With Hook
A compact Raspberry Pi Zero enclosure with a snap-on lid and a vertical C-shaped hook on the back wall. The hook clips sideways onto a vertical screw or rod, so the case hangs beside a printer such as the Monoprice Select Mini. Interior fits the 65 × 30 mm board, with 58 × 23 mm standoffs and pins Cut-outs for microSD, mini HDMI, USB and power Vent slots along the back wall Hook bore sized for a 5 mm screw shank, with a 3.8 mm snap opening Lid prints flat beside the case, with no overlapping parts
Inverted Glue Bottle Stand
Keep viscous liquids like glue or ketchup primed and ready at the nozzle. Storing bottles inverted ensures immediate dispensing, eliminating the wait for a half-empty bottle to drain toward the cap. The stand is designed with a stable tripod base and precise clearances to hold the bottle securely while catching any rogue drips. Design specifications: Sized to cradle a 45mm bottle body Integrated 30mm drip cup positioned directly under the nozzle Beveled entry ring guides the bottle smoothly into place Tapered support arms print cleanly without support material Wide footprint prevents tipping even with a full, top-heavy bottle
J-Shaped Pocket Edge Fabric Clip
A 40 mm wide J-clip that grips a fabric pocket edge. A flat back plate holds two countersunk M3 screw holes, and a sprung leg closes back toward it. Remix hooks Relaxed gap: 1.5 mm, set by the leg angle (about 6°). Raise it for thick cloth, lower it for more grip. Tooth: 0.8 mm round bump 12 mm from the leg tip. Make it larger, or remove it for a smooth clamp. Mouth flare: 25° over the last 6 mm. A wider flare helps with thick fabric. Bend radius: 3 mm inner, with 2.6 mm walls. Print with layers running along the width so the bend doesn't split. Holes: 25 mm apart, 20 mm up from the bottom, 3.4 mm with a 6 mm countersink. Change the spacing to match a mounting pattern. Plate is 45 mm tall and the leg is 42 mm long. It pairs well with PETG or nylon for spring.
Sliding Tray With Lid Handle
A 78 x 47 x 125 mm vertical tray that slides into a box, topped by a lid that doubles as a pull handle. Four compartments, lowered front lips and a grooved finger tab make loading and pulling easy. Remix hooks Wall and floor: 1.2 mm walls, 1.8 mm floor. The floor absorbs the leftover height so the 56 mm lower row and 66 mm upper row fit the 125 mm total. Lip height: 6 mm front lips with a 22 mm round dip. Raise the lip for deeper pockets, or widen the dip for bigger fingers. Dividers: the vertical wall sits at 38 mm from the left, and the right side is split by a horizontal wall. Move either to resize the compartments. Ribs: 2 x 2 mm guide ribs on the side walls, full height. Change them to match the clearance of the box. Lid: 90 x 56 x 8 mm, flush at the back, with 45 degree chamfered underside edges and three 1 mm grooves on the 30 mm tab. Pairs with any box sized around the 82 mm tray. Prints upright with no supports.
Zauberstab 3.5
What it's for Zweiteiliger Zauberstab mit Griff und Spitze für eine UV-Taschenlampe. Außen ist ein glatter Stab mit schmalen, aufgelegten Teigsträngen, die sich spiralförmig um ihn winden. Innen verschließt ein Bajonett mit Rastnocke. Dimensions Griff: 87 mm hoch, 85 mm Innenhöhe, Bohrung Ø 21,8 mm Spitze: 135 mm gesamt, verjüngt sich nach oben, Lichtkanal innen hohl Glatter Kern Ø 26,4 mm, vier Stränge, ca. 0,8 mm breit am Boden und nach oben schmaler Vier Löcher Ø 3,75 mm im Boden Remix ideas Mehr oder weniger Stränge Stränge dicker für stärkeres Relief Andere Windungszahl über die Höhe
Drawer Sleeve Box With Mounting Pad
Open-top rectangular sleeve, 86 x 52 x 127 mm, for a sliding drawer. Smooth interior, 1.6 mm floor, sides and front, 2.4 mm back wall. A raised 40 x 40 x 3 mm pad on the back carries two M3 nut traps. Remix hooks Pad position: top edge sits 10 mm below the rim; pad is centered in X. Move or resize freely. Nut traps: 5.7 mm hex, 2.5 mm deep, 25 mm apart, with 3.4 mm blind holes behind them. Blind holes stop 0.8 mm short of the inside; thicken the back wall to go deeper. Edges: 3 mm vertical rounding, 6 mm 45° bottom chamfer (prints without supports). Drains: two 3 mm holes at X = ±20 mm. Pairs with a matching drawer 3 to 4 mm smaller in each direction.
Car Coffee Tray shj
A rectangular car coffee tray, 124.7 × 107.4 mm and 10 mm tall, with a raised 4 mm rim and a recessed floor to keep cups and items in place. "meet me in SHJ" is engraved 0.8 mm deep into the floor in the bottom-right corner. Remix hooks Text weight: the letters are 7 mm tall with strokes thickened by 0.3 mm per side. Raise that for a bolder engraving, or drop it to return to the plain font weight. Text size and position: 7 mm size, 5 mm in from the rim. Change the inset to move it, or switch the alignment to centre it. Rim and floor: 4 mm wall and 4 mm floor thickness. A taller rim holds more, a thinner floor saves filament. Pairs with: a non-slip mat under the base, or a cup-sized ring added to the floor.
Gaveta Vertical Mini APH Pocket
Uma gaveta vertical de bolso, no espírito de um canivete suíço de primeiros socorros: o puxador largo no topo é também a tampa, e puxá-lo para cima faz a bandeja subir pelas guias, expondo os itens. Notas de projeto Corpo 86 × 52 × 127 mm, parede de 1,6 mm, dois drenos de ø 3 mm e furo de ø 4 mm para cordão. Bandeja 78 × 47 × 125 mm com tampa de 90 × 56 × 8 mm, recorte de dedo e divisórias. Clipe em J de 40 mm, 2,6 mm de espessura, impresso deitado. Pensado para PETG, sem suportes. Versão simplificada: dentes de retenção, rabo-de-andorinha, berço do oxímetro e batente liberável ainda não modelados.
Railing 2 m Long, 1.5 m High
A railing panel with the dimensions written on every part, so nobody has to dig out a tape measure to check which bar is which length. Overall: 2000 mm long, 1500 mm high, 50 mm deep Posts: 50 x 50 mm, 1500 mm tall, labelled with height Top and bottom rails: 1900 mm between posts, 80 mm tall Bars: 12 vertical bars, 20 x 20 mm, 1260 mm long, 150 mm centre-to-centre Labels: raised 1 mm text on the front face (top rail length, 150 mm gap marks, bar lengths, post heights) Printing: designed at full size, so scale down or split into sections for a normal printer
Fabrication-Ready Welded Railing explode
A heavy-duty 2-meter railing section designed for real metal fabrication. The components are drafted with realistic 2mm root gaps at every joint and heavy 4mm chamfers simulating weld bevels, so the model accurately reflects standard weld-prep fitment. Overall Size: 2000mm long by 1500mm tall. Post Size: 60mm square stock. Rails: 50x40mm profile, with a 120mm bottom clearance. Balusters: 20mm square, 150mm on-center spacing. Joinery: Ends are shortened by 2mm and heavily chamfered to provide a realistic V-groove root gap for welding.
Wide Hook With Tall Front Lip
A small wall-side hook, 20 mm wide and 15 mm deep, with a 20 mm back plate, a flat 3 mm arm and a 50 mm upturned front lip. Remix hooks Width (20 mm): the one value shared by the plate, arm and lip. Widen it for heavier loads or narrow it for tight spots. Lip height (50 mm): lower it to around 10–15 mm for a simple catch, or keep it tall to hold flat items upright. Back plate height (20 mm): raise it to leave room for a screw hole or two. Arm thickness (3 mm): thicken it if the hook will carry weight. Pairs well with countersunk screw holes in the back plate or double-sided mounting tape.
Industrial Pull Plate
A heavy-duty mounting plate featuring an integrated pull tab and precise counterbored holes. Designed for easy handling and a flush fit with socket head hardware. Mounting Interface: 4x 4.3mm thru-holes with 6.5mm counterbores (4mm deep) Spacing: 72mm x 40mm pattern Convenience: Rounded 35mm pull tab with a 10mm grip hole
Offenes Schreibtischregal mit Rampe
Schreibtische müllen immer von der Mitte her zu. Dieses Regal hebt den Kleinkram aus dem Weg und teilt die Fläche in der Mitte mit einer harten Rampe – links liegt das Fach tief für flaches Zeug, rechts hoch, damit darunter noch Platz für größeres Zubehör bleibt. Alles bleibt zugänglich und nichts verhakt sich. Eckdaten Spannweite: 450 mm Standfläche (Tiefe): 180 mm Höhe: 250 mm Druck: Wird flach auf der Rückseite liegend gedruckt und kommt komplett ohne Stützstrukturen aus.
Miniature Tractor Tire With Separate Rim
A miniature tractor front tire that stops the usual toy-wheel problem: thin tread that wears flat and a rim glued in place. This one has deep chevron lugs and a separate rim that presses in. Tire: 70 mm outer diameter, 40 mm wide, 44 mm bore, 14 zigzag lug pairs about 6 mm tall Rim: 43.6 mm barrel, 50 mm flange on one side, 10 mm axle hole Print: tire and rim as separate parts, flat on the bed, no supports needed for the rim; tire lugs print without supports Rim fits with 0.2 mm radial clearance
door lock
Rectangular block, 100 mm long, 24 mm wide and 15 mm tall, with a 16 mm wide by 11 mm deep groove running the full length along the top centre. The groove size is engraved into the groove floor as "16 x 11 mm". Overall size: 100 x 24 x 15 mm Groove: 16 mm wide x 11 mm deep, open at both ends Side walls: 4 mm; floor: 4 mm Engraving: 0.6 mm deep, readable from above Prints flat with no supports
Monitor stand v2
A one-piece stand for a 200 × 110 × 18 mm tablet, holding it at 70° from horizontal. Two angled supports are joined by a solid crossbar, with a front lip and a backrest. Fitment Supports are 20 mm wide, centred 100 mm apart, so they land at 50 mm and 150 mm along the tablet's 200 mm width. Overall stand width is 120 mm; the tablet overhangs 40 mm each side. Slot depth is 20.5 mm for an 18 mm tablet. Front lip covers only the bezel. Check before printing Measure the tablet's thickness with any case on. Anything over about 20 mm will not enter the slot. Does not fit Tablets thicker than 20 mm, or portrait-orientation use, which this stand is not shaped for.
Print-In-Place Advent Drawers
What it's for This is a fully assembled, print-in-place advent calendar and organizer. All 24 numbered drawers print inside the frame at once with no assembly required. It features integrated sliding tracks and built-in stops that prevent the drawers from being accidentally pulled out all the way. The design is oriented to print flat on its back. This allows the raised numbering and front pull-tabs to print perfectly on the top surface without any supports or bridging issues. Dimensions Overall Assembly: 169.5 mm wide × 169.5 mm high × 42 mm deep. Drawer Outer: 39.5 mm wide × 25.5 mm high × 39.5 mm deep. Drawer Inner (usable): 36.5 mm wide × 22.5 mm high × 36.5 mm deep (perfectly sized for standard 35 mm tealights or small treats). Clearances: 0.5 mm on all sides for smooth, bind-free sliding. Print notes Supports: None. The entire unit bridges perfectly on its own. Build Plate: Fits easily on a 180 × 180 mm bed (like the Bambu Lab A1 Mini). Clearance: Designed with extremely generous 0.5 mm gaps. Ensure your printer is not severely over-extruding to guarantee the drawers snap free immediately.
Monolithic Grid Advent Calendar
A complete, print-in-place Advent calendar designed specifically to fit on the Bambu Lab A1 Mini (180x180x180 mm build volume). It features exactly 24 sliding drawers arranged in a space-efficient block, numbering from 1 to 24 sequentially. The top two rows contain 8 larger drawers perfect for bigger treats, while the bottom four rows hold 16 smaller drawers. Print-in-Place Design Ready to Slide: The drawers and frame are printed together as a single unit. Tolerances are tuned (0.4 mm on sides and bottom, 1.0 mm on top) so the bridging above each drawer naturally sags without fusing the parts together. Zero Assembly: No separate rails, glue, or snap-fit parts to mess with. Easy Grip: Each drawer features a neat little half-circle finger notch at the top, making them easy to pull open. Printing Tips No Supports: Do not generate supports, as they will fill the internal gaps and fuse the drawers to the frame. Cooling: Ensure your part cooling fan is running high so the bridges above the drawers stay relatively crisp. Material: Standard PLA works perfectly. White gives it a clean, classic winter look.
Monolith — MagSafe Dock
Monolith is an architectural desk stand built specifically for the Apple MagSafe charger. It's designed to read as a single sweeping piece of tech, dropping the wire invisibly through the core and directly out underneath the base pad. Features Perfect Fit: Toleranced to 56.5mm to lightly grip the standard MagSafe puck. Seamless Route: The cable threads cleanly inside the stem and travels down to the desk surface. Ergonomic Tilt: Features a 50-degree backrest optimized for at-desk use and FaceID unlocking. Vented Spine: Deep architectural slots line the back for a leaner profile.
608 Bearing Level Wind Shaft
A continuous reversing lead screw shaft, designed to drive a reciprocating carriage without needing the motor to switch direction. Ends are dimensioned for a 608 bearing (8 mm bore). The track is a 5 mm spherical U-groove; pair it with a 4.5 mm or 4.8 mm round follower pin so it can swivel without binding at the turnarounds. Total effective travel between reversing points is 75 mm.
Metabo Schlauchadapter 35mm zu 39mm
Wofür es ist Ein massiver Werkstatt-Schlauchadapter, der speziell für Metabo Industriesauger ausgelegt ist. Er verbindet Schläuche oder Anschlüsse mit 35 mm und 39 mm Außendurchmesser. Dimensionen Gesamtlänge: 85 mm Steckbereich schmal: 45 mm Länge, 35 mm Durchmesser (gerade) Steckbereich breit: 30 mm Länge, 39 mm Durchmesser Wandstärke: 2,5 mm Druckhinweise Ausreichend Perimeter (mindestens 3-4) drucken, damit die Wandung stabil und luftdicht bleibt. PETG oder ABS sind für den harten Werkstatteinsatz zu empfehlen, PLA geht bei leichterer Beanspruchung auch in Ordnung.
Brændpunktsskinne til ellipsetegning
En flad skinne med 11 nummererede huller og to pinde, der bruges til at tegne ellipser med en snorløkke. Skinnen er 170 × 18 × 4 mm med afrundede hjørner (radius 6 mm), og hullerne sidder med 15 mm afstand. Remix-muligheder Antal huller: n = 11 giver 170 mm i længden. Brug et ulige tal for at beholde 0 i midten. Hulafstand: 15 mm. Mindre afstand giver finere trin i excentriciteten. Hjørneradius: 6 mm. Kan sættes op til ca. 8 mm uden at ændre bredden. Pinde: Skaft 8 mm, krave 11 mm, hals 5 mm til snoren. Gør skaftet 0,2 mm tykkere, hvis pindene skal sidde fast. Passer til: En snorløkke på ca. 200 mm indvendigt og et A4-papir.
Sonderkerzen 1.2
What it's for Vier hohle Kerzenkörper in abgestuften Höhen mit Wachstropfen-Optik. Der Boden ist per Bajonettverschluss abnehmbar. Kleine Rastnasen im Verriegelungsschlitz lassen den Verschluss spürbar einrasten, damit er sich nicht versehentlich löst. Dimensions Höhen: 110, 105, 100 und 95 mm Außendurchmesser 45 mm, Innendurchmesser 37 mm Teilung 25 mm vom Boden Vier 1-mm-Löcher, 16 mm unter dem oberen Rand Remix ideas Rastnase höher oder niedriger für mehr oder weniger Haltekraft Andere Höhenstufen Weitere Tropfenmuster
Need a part that doesn't exist yet?
Start building →