3D-printable decor & display pieces
Lithophane shades, planters, trophies, wall art and display models. Browse what makers built, or describe the exact piece you want and Printy makes it.
Need one that fits your exact measurements? Start building →
Newest
Spot Light Trophy Sign Stand
An upright "Spot Light" sign on a flat base plate that glues to the top of a trophy base. Two searchlight towers flank the sign, with flat beams fanning upward in the style of a classic studio logo. Flat 96 x 36 x 3 mm base plate with a flat underside for gluing Upright sign panel, 60 mm wide, with raised Alfa Slab One lettering facing front Two searchlight towers with angled lamp heads Thin crossing and outward beams, about 66 mm tall overall Printable without supports; beams are 2 mm thick, so handle with care Trim the base plate or scale the model to match the trophy's top surface.
One-Piece Vintage Car Model
What it's for This compact one-piece vintage car model has an exposed engine up front, fenders over four wheels, and a gold grille with two round headlamps. The open engine bay holds a blue engine block with six cylinder stacks, a cover plate and an exhaust pipe down each side. Behind it sit a low dash and two open bucket seats with backrests — an open roadster with no cab, and a windshield built as an upright open frame rather than a glazed screen. The weathered brown frame includes two chassis rails joined by three cross members, the upright windshield frame, and a roll-frame around the seats with four corner posts and a top rail loop. A dark gray steering wheel sits on the left side ahead of the left seat, with a tilted column, a ring and two spokes. A footwell is cut into the floor between the windshield frame and the seats, and the steering column stands on that floor. The body, fenders, seats, wheels, grille/lamp area, exposed engine and frame are separated by colour, which makes it easier to plan a paint scheme or a multi-colour print. Use it as a small display piece, a shelf ornament or a painting project. Dimensions Body: 24 mm across × 60 mm front-to-back × 8 mm high; seats, engine and frame rise above it. Frame: 24.5 × 58 × 24 mm; chassis rails 3 mm thick, corner posts 2.5 mm square. Wheels: 38 × 51 × 25.3 mm; the widest point of the car is about 38 mm across at the wheels. Fenders: 27 × 54 × 2.5 mm. Grille and lamps: 24 × 5.5 × 11 mm. Exposed engine: 16.9 × 20 × 12.5 mm. Seats: 21 × 12 × 11 mm; backrests stand 11 mm tall and about 3 mm thick. Footwell: 18 mm wide × 10 mm long, leaving about 2 mm of floor. Steering wheel spokes: 1 mm. Print notes Print the body flat on the bed so the wheels stay clear of the build plate. The model prints as one piece and needs no assembly; the wheels are fused to their axles and do not roll freely. The exhaust pipes are thin, about 2.5 mm across; handle cleanup gently, or thicken them if they snap. The steering wheel spokes are 1 mm and are the weakest detail, so take care when cleaning the print. The footwell floor is about 2 mm thick; take care when cleaning it out. Check the roll-frame and upright windshield frame when removing the print. Remix ideas Recolour the body, fenders, seats, wheels, grille/lamp area, engine and frame to match a period livery or to highlight the exposed engine. Scale the model for a larger display piece or a smaller desk ornament. Keep the fused-wheel layout for a simple one-piece print, or use the wheel and axle area as a starting point for a free-rolling variant. Change the engine details in the open bay, reshape the seats, or add rivets and bends to the chassis rails to push the weathered look further. Extend or simplify the roll-frame, or swap the steering wheel for a different period wheel.
Pioneer-Era Wright Flyer Biplane Model
A detailed tribute to the 1903 Wright Flyer, the fragile-looking biplane that first took powered flight. Two ribbed wings span about 123 mm, held apart by open strut bays, with a double-surface front elevator on booms ahead, twin rudders behind, and long skids beneath. An engine, a prone pilot, and two pusher propellers complete the machine. Design notes Ribbed upper and lower wings with open strut bays. Front elevator mounted on booms; twin rudders at the tail. Prone pilot lying on the lower wing, matching the Flyer’s flight position. Two pusher propellers shown as simplified flat blades. Chain drive and wing-warping wires are omitted. Grouped as Wings, Wood Frame, Engine, Pilot and Propellers.
16 mm Arched Door Frames and 15x20 Windows Set
Six arched door-and-frame pieces and twelve rectangular windows for an OO scale (1:76) house, laid out flat on the plate. What it fits Door frames: 16 mm wide, 2 mm deep, with a semicircular arch top. Each has a door printed in one piece with it. Windows: 15 x 20 mm, 1.6 mm deep, with a transom bar across the middle. Check before printing Measure the wall openings against the 16 mm frame width and 15 x 20 mm window size. The door relief is 0.4 mm, so use a fine layer height. Not covered The windows are not arched and have no glass pane. Sizes are not matched to any other scale.
Funfair Swing Ride with Crank, 100 mm Base
Funfair swing ride with a hand crank on top. Turning the crank spins the canopy and seat ring around a fixed central pin, and each of the six seats hangs from a captive ball joint so it swings outward as the ride turns. Base: 100 x 100 x 6 mm plate with a 30 mm column and 14 mm mast Spinning top: 70 mm seat ring and cone canopy on a 8 mm pin, 0.3 mm bearing clearance Seats: six, each on a 7 mm captive ball with a 3 mm rod, printed in place Crank: 30 mm arm with a 7 mm handle on top of the canopy Print in place, no supports needed for the base; the ring cavities bridge over the balls Overall height about 112 mm
Male SandWing Dragon with Spread Wings
A standing four-legged male SandWing dragon with two fully spread wings, a continuous sail along the head, neck and spine, and a curved stinger at the tail end. A gold hoop earring passes through the left ear. Colors: sandy-gold body, cream underside, ivory horns and claws, black eyes Wings: continuous membranes on finger-like supports Tail: tapers directly into the curved stinger Base: low flat plate under all four feet
Stemmed Goblet With Flowers and Vines, 125 mm
Clear drinking goblet, 125 mm tall with an 80 mm rim and a 56 mm round foot. Ten raised five-petal flowers sit around the outside of the bowl, each with a vine stem that runs down the bowl wall. Five of the vines continue and spiral down the stem toward the foot. Flowers and vines are on the outside only; the inside stays smooth Vine thickness: about 2.2 mm, raised from the surface Five vines wind down the stem; the other five end at the base of the bowl Material: clear PETG suggested Supports: likely needed under the bowl flare
Placa Retangular com Borda Dourada e Texto
Placa retangular de 95 x 40 mm e 2 mm de espessura, com uma margem dourada fina recuada da beirada e a frase "Obrigado ao Cb PM Gabriel do Sd BM Luís Gustavo" em relevo, em duas linhas. Placa: 95 x 40 x 2 mm Margem dourada: 1 mm de largura, recuada 3 mm da beirada, 1 mm acima da superfície Texto: em relevo de 1 mm, centralizado dentro da margem Pensada para impressão multicolor ou pintura posterior
Pijl
A two-part LED arrow: an open-top frame and a separate flat top plate, printed side by side and pressed together after printing. The assembled arrow is about 188 mm long, 84 mm across the widest part of the head and about 15 mm thick. The two barb corners of the head sit forward toward the tip for a more open head profile. The tail matches the head at 84 mm across the far end and narrows to 28 mm where it meets the arrowhead, with both long edges bowing inward about 4 mm at the midpoint before flaring back out, so the arrow reads as a wide-fletched, waisted shape rather than a plain bar. The frame is 15 mm deep with 2.4 mm walls and a 2 mm floor, leaving a deep interior for an LED strip; the cavity is completely empty, with no posts or ribs to shadow the light. The cable enters through a round 10 mm hole in the floor, set into one tail corner about 15 mm in from the tail end and 28 mm off the centre line, with room around it for the walls; the wiring drops straight down and out of sight. The top plate is a single flat 2 mm layer with an oversized edge. A 0.8 mm deep groove, about 2.4 mm tall, runs around the inside of the frame walls at the top rim and is open at the top edge. Press the plate down from above and its edge slips into the groove, landing on the ledge below so it sits flush with the rim. The fit is snug: the plate edge sits about 0.1 mm from the groove wall, so it fills the recess with almost no play. Because there is no overhanging lip, the grip comes from that close edge fit; if it feels loose, a thinner gap of about 0.05 mm gives more bite, and if it is too tight to press in, open it to about 0.15 mm. A 2 mm plate this long is stiff, so press it in at one end first and work along. Both parts sit flat and the cable hole is a plain vertical bore, so the print stays simple on a standard 0.4 mm nozzle. The frame is 188 × 84 mm and the plate about 182 × 79 mm, so the two sit side by side on a 220 × 220 mm bed with a little margin to spare. Remix hooks Footprint (188 mm long, 84 mm head): the size is a choice, not a fixed value. Scale down for a desk-size arrow, or scale to your own bed limit and re-check that the plate and frame still fit side by side in one go. Head shape (84 mm across; barb corners sit toward the tip): push the corners back toward the tail for a sharper swept-back profile, or bring them further forward for a more open head; keep the plate outline matched to the frame. Tail taper and curve (84 mm at the far end, 28 mm where it meets the head, about 4 mm inward bow): narrow the tail end back down for a fan-tailed look, straighten the long edges toward a constant shaft, or deepen the curve for a more waisted silhouette. Frame depth (currently 15 mm): the main volume choice. Shrink it for a slimmer arrow, grow it for a deeper strip or to hide a battery holder; check that the top plate still lands flush at the rim. Wall and floor thickness (2.4 mm and 2 mm): thick enough to stay opaque and rigid at this size. Thinner walls let more light through the sides; thicker ones make a sturdier shell for outdoor use. Plate fixing (flat 2 mm sheet; 0.8 mm deep groove at the top rim, plate edge about 0.1 mm from the groove wall): the first thing to tune. A deeper groove or a smaller edge gap gives a tighter hold; a shallower groove or more gap makes the plate easier to press in. Add a thin lip over the groove for a true snap, or clips and screw bosses if you want a different hold. Thicken the plate for more diffusion. Floor cable hole (10 mm, in one tail corner about 15 mm from the tail and 28 mm off centre): widen it for a chunky connector, move it to the opposite tail corner, or shift it along the shaft if your wiring runs from a different direction. Two or three small holes in a row would suit a multi-colour strip installation. Joint style: the open-top rim groove is the current no-glue method; a lip, small clips, screw bosses or a glued seam are fair variants if you want a permanent or firmer assembly. Pairs with An LED strip cut to fit the cavity, and the plate printed in a white or natural diffusing filament. Because the frame is a closed outline with a flat back, a row of arrows in the same style prints as a matching set.
Cwmlech Manor Steampunk Horseless Carriage
A miniature Victorian steampunk horseless carriage in the spirit of The Ghost of Cwmlech Manor, arranged in three clear zones from front to back. Up front sits the cylindrical boiler with two round brass headlights and a tall black smokestack, banded in brass with a flared cap. In the middle, the brown padded seat and backrest ride on the black frame with the steering column just ahead of them, open to the air. Behind, a short horizontal tank with ring bands carries a brass gear on each side and copper piping that runs along its upper flanks and forward to the engine, passing overhead on its way. Thin-spoked wheels with dark rims roll on straight through-axles, and the whole thing keeps a low, mechanically believable silhouette with a vintage industrial finish. Built in three zones Front: cylindrical boiler, tall banded smokestack with flared cap, two round brass headlights on posts, and the engine housing Middle: brown padded seat and backrest on the frame, with the steering column, ring and cross grip just ahead Rear: short horizontal tank on saddle supports, a brass gear on each side, and copper pipes along its upper sides Four round, thin-spoked wheels with dark rims, all the same size, on straight through-axles Print notes The carriage prints as one connected solid with thick, simple shapes and no floating parts, so it suits a beginner-friendly print. The wheels sit level on the plate. The viewer colours show the intended finish: black body, brown seat, copper pipes, brass fittings, wheel spokes and rims — the part runs roughly 86 mm long, making it a desk-scale piece. The forward pipes pass above the seat, so check their clearance before you slice.
Placa Radassa Pacifico, Base Reta
Placa orgânica com o nome "Radassa" em alto relevo, fonte Pacifico, e base reta para apoio. Medidas a conferir Placa: cerca de 110 × 35 mm, 3 mm de espessura. Relevo do nome: 3 mm acima da placa. Base reta em Y = -15 mm, com apenas 3 mm de espessura; sozinha, a placa tende a tombar. Use um suporte ou apoio. Não inclui Furos de fixação. Borboletas.
Blank-Sign Mandarin Storybook Town
A tabletop storybook town in the spirit of a classroom diorama: four pastel buildings along a back row, a road with parked cars, and a park with banners, people, trees and benches. Every sign and banner is left blank, ready for hand lettering with paint pens or stickers. Where each word goes 医院, 图书馆, 商店, 社区中心: white plaques on the four building fronts (hospital has a red cross) 工作: small plaque on the shop 服务: orange banner in front of the library, with people nearby 公园: green banner at the park 活动, 一起, 参加: banners above groups of people 社区: blue banner near the road Extra features Road, path, trees, people, benches, cars and streetlights
Street Lamp Base with Domed Foot
A miniature street lamp base for a 1:64 diorama. A domed foot with a flat 7.2 mm bottom rises into a straight 5.5 mm shaft, 10 mm tall overall, with a centred 2 mm through-hole. Height: 10 mm Shaft diameter: 5.5 mm Foot diameter at the flat bottom: 7.2 mm Dome height: 6 mm Through-hole: 2 mm, fully open One solid body with a flat bottom, no decoration
Baby Dragon Figurine, 64x80 mm Base
A baby dragon figurine on a flat 64 x 80 mm base plate, built as one solid piece for FDM printing. Fit and print notes Four short legs, rounded body, small horns, tiny wings and a thick curved tail, all fused to the body. Check before printing: the bed must take about 64 x 80 mm. Prints without supports on its flat base in most cases. The horns and the wing tips are the only overhangs. Not scaled for any particular display stand or holder.
Lotus Flame LED Tealight Holder
A Diwali LED tealight holder: a pointed, flame-shaped white frame stands on a round base, with a red lotus panel set inside it. The lotus is cut clean through the panel, so the LED glow shows through from the front cup. Five red petals wrap the cup, and two large white petals sweep out to the sides. Designed for battery LED tealights only, never real flames. Remix hooks Cup size: 41.6 mm bore, 20 mm deep, 47.6 mm outside. Change the bore for a different tealight brand. Open top, so the LED lifts straight out. Flame silhouette: one width function sets the outline (about 40 mm half-width, 136 mm tall, standing on a 5 mm, 85 mm base). Change the exponents for a slimmer or fuller flame. Lotus pattern: the cutouts are a short list of ellipses (centre petal 11 x 44 mm). Add a ring or swap the shapes, and keep a 2 mm or wider web between openings. Colour split: red panel and front petals, white everything else. The panel sits in a 1 mm slot with 0.1 mm clearance on each face, so it prints flat and drops in. Swap in blue for an accent. Pairs with: a flat LED tealight, or a second panel with a different motif. Starting dimensions Height about 140 mm Width about 120 mm across the outer petals Depth about 85 mm, set by the base Frame 8 mm thick, panel 3.5 mm thick
Lotus Stem Diya Stand
What it's for A diya stand shaped like a lotus on a stem. A low lotus bloom serves as the base, a slim stem rises from it, and an open lotus of petals cradles the diya cup at the top. There is no separate podium. Dimensions Base lotus spread: roughly 60 mm across Stem: about 25 mm of slender column with a decorative bead Diya seat: 40 mm diameter recess Overall height: about 48 mm Remix ideas Resize the seat for a larger or smaller diya. Add more petal layers for a fuller bloom. Lengthen the stem for a taller stand.
Curly Coated Westie Figure
A white West Highland terrier figure sized for soft, squishy TPU printing. The coat is built from chunky curls, with a heavy fringe over the eyes and hair across the top and sides of the head. Short, stubby legs Floppy ears hanging down the sides of the head Curly coat on body, chest, haunches and head Bare face below the nose Dark nose and eyes, flat underside for stable printing Print in TPU with low infill for a squishy feel.
Small City Model with Park and Trees
A 230 × 170 mm town plate laid out as a small city: a row of five tall buildings along the back, a main road with crosswalk, side buildings, houses, cars, streetlights and a park with a pond, crossing paths, a bench, people and many trees. All lettering has been removed. Base: 230 × 170 × 4 mm plate Park: lawn, pond, two crossing paths, 19 trees, bench City: buildings 14–34 mm tall with windows and doors Extras: streetlights, cars, people, crosswalk Print: no supports needed for most parts; trees are cones and print best with a slow top layer
Engraved Name Block with Ogee Edges
A solid 4 x 3.5 x 1 in block with "Francisco Suarez" indented into the 4 x 1 in front face. All edges carry a Roman ogee profile: a concave sweep flowing into a convex bead. Size: 101.6 x 88.9 x 25.4 mm Name indented 1.5 mm, centered on the front face Smooth S-curve edge profile on all twelve edges Flat base, prints without supports
2
A conical vase, 150 mm across the base, 200 mm across the top and 300 mm tall, with 10 mm walls and floor. Maple leaves cover the outside in staggered rows, 9 rows of 16. Remix hooks Leaf density: 16 leaves per row and 9 rows at 30 mm spacing. Fewer, larger leaves give a bolder look. Wall thickness: 10 mm. Drop it to 3–4 mm to save material, or keep it thick for stability. Taper: base radius 75 mm, top radius 100 mm. Swap them for a flared-in neck. Leaf relief: 3 mm deep. Use less for a subtle texture. Pairs with: a glass jar liner for fresh flowers, since the walls are not waterproofed by the print itself.
Eukalyptuskranz für 21-mm LED-Stabkerzen
Adventskranz-Grundform mit dichtem Eukalyptuslaub und vier integrierten Kerzenhaltern für LED-Stabkerzen mit 21 mm Durchmesser. Passung Kerzenbohrung: 22,6 mm Durchmesser, 20 mm tief, mit Einlauffase – passend für 21-mm-Stabkerzen. Vier Halter im Abstand von 90°. Kranz ca. 200 mm Außendurchmesser, ca. 45–50 mm hoch. Vor dem Druck prüfen Den tatsächlichen Kerzendurchmesser nachmessen; bei Kerzen über 22 mm sitzt die Bohrung zu knapp. Druck Blätter sind unter ca. 40–48° nach oben geneigt, der Ring hat eine ebene Unterseite – Druck ohne Stützen. Passt nicht für Kerzen mit Durchmesser unter ca. 20 mm (sie stehen locker).
Smart Goggles Frame with Hollow Arms
Smart goggles frame with two temple arms that are hollow and open on the inside face, plus separate lens caps, an electronics box with cap, and hinge pins. What it fits Frame hinge pockets take the 11 mm wide arm tabs on vertical 3.4 mm pin holes. Hinge pins are 3.0 mm, so they fit those holes with clearance. Check before printing The arm cavity is open on the inside face and has no cover. Wall on the outer side is about 3 mm. Speaker slots and the right-arm USB-C and switch cutouts remain on the outer wall. Does not include No cover plates for the arms. No hinge stop or spring.
Плоский круглый диск 80 мм
Простой плоский диск диаметром 80 мм и толщиной 3 мм с гладкими поверхностями с обеих сторон. Подходит как заготовка для медальона, жетона или основы под надпись и рельеф. Диаметр: 80 мм Толщина: 3 мм Обе стороны плоские, печать без поддержек
Soporte de tarjetas con estrella grabada
Bloque rectangular con una ranura central para tarjetas y una estrella de cuatro puntas con lados curvos, grabada hacia el interior de la cara frontal. Bloque de 115 x 25 x 20 mm con bordes achaflanados Ranura de 4 mm de ancho y 10 mm de profundidad, de extremo a extremo Estrella curva de 16 mm de punta a punta, hundida 1,5 mm y centrada en la cara frontal Se imprime sin soportes apoyada sobre su base
Need a part that doesn't exist yet?
Start building →