3D Model Gallery
Every one of these started as a sentence — real dimensions, real holes, print-ready STL. Remix any of them, or describe the part you need and Printy builds it. Start building →
Newest
Utilitarian Thin-Walled Pipe
A bare-bones, precision-cut cylindrical sleeve evoking raw industrial hardware. It carries a uniform 1.5mm wall over its entire span, engineered strictly for custom slip-fit or sleeving applications where clearances are tight and material cannot be wasted. Dimensional Specs: Inner diameter: 65 mm Outer diameter: 68 mm Total length: 65 mm
Stealth Pillion Cowl Cap
A sharp, faceted pillion cover that borrows heavily from the brutalist angles of modern stealth fighters. Designed to sit directly over a standard passenger seat rather than replacing it, this cap runs extremely low-profile to keep the tail looking clean when riding solo. Fastening Internal Anchors: Four distinct strap loops are tucked into the side margins of the hollow cavity. Routing: Run flat webbing (up to 25mm wide) side-to-side through the loops and directly underneath the seat pan. Fitment: Wide, generic clearances mean it acts as a floating cap, letting the straps pull it snug without needing latch-specific hardware.
Paper Towel Core Stabilizer Cap
A tapered palm-rest cap designed to drop into the top of a standard kitchen roll. It provides a wide, smooth surface for your hand to press down on while tearing off a sheet, stabilizing the unit without pinching the paper towel itself. The tapered body ensures a loose spinning fit inside standard cardboard cores, while the hollow interior clears the paper towel holder's central upright. Fitment Measurements Cardboard Core Insert: Tapers from 41.5mm at the top down to 36mm at the base. Upright Clearance Bore: 32mm internal diameter. Palm Rest: 80mm wide. If your printed upright is wider than 32mm in diameter, the internal bore will need to be expanded to fit.
Pi 5 Tower Case
This is a two-part enclosure built to house a Raspberry Pi 5 alongside a tall stack of PCIe shields. Because expansion boards vary wildly in where they drop their ports, this shell skips the millimeter-perfect holes in favour of massive front and rear bays. It provides 50mm of internal headroom, easily clearing an active cooler, a 2.5G Ethernet shield, and an NVMe board stacked together. Remix Hooks Cover Height (cover_h): Set to 50mm by default. If your Waveshare stack sits higher, push this up. Port Bays: The large cutouts on the cover are generic rectangles spanning almost the entire width of the case. If your shields use a weird side-exit layout, you'll want to punch a new hole through the Y-axis wall. Standoffs: The base includes 4mm standoffs (standoff_h) with 2.4mm alignment pegs matching the standard Pi 5 mounting footprint (58x49mm).
90x60mm Campaign Magnet-final-final-super-final
A three-colour stepped campaign magnet formatted for a 90x60mm footprint. Designed to print cleanly with two manual filament swaps. Fitment Magnets: Four 6.05mm x 3mm disc magnets, set into the rear face. Layer Heights: Blue base to 3.6mm, white layer to 4.6mm, red top layer to 5.6mm. Features a classic bell-tower schoolhouse and a reshaped apple graphic flanking the bottom text line, with adjusted margins across the middle lines to tighten up the vertical spacing.
1.95" x 0.195" Chamfered Sleeve
A simple sleeve spacer or bushing. Features: Outer Diameter: 1.95 inches Inner Bore: 0.195 inches (through-hole) Overall Height: 2.5 inches Internal chamfers on both ends of the bore to ease insertion. Check your shaft diameter and required clearance before running off a print.
Motorcycle Numberplate Spray Deflector/Mud Guard
That perfectly aligned stripe of wet road grime the rear tire slings exactly past the bottom edge of the plate and up the center of your jacket is miserable. Tail tidies look good, but they leave the dead center of the wheel completely unshielded. This is a wedge deflector that clips directly onto the bottom edge of the numberplate. It projects a downward-angled, 18mm shelf backwards toward the wheel, catching that specific arc of water and directing it back at the road. The ends are heavily swept to match the sharp lines of modern sport bikes like the Z-series. Fitment & Printing Slot Width: 3.0mm, deep enough (15mm) to swallow standard plates. Features an internal 0.4mm friction ridge to bite onto the plate. (If your plate is very thin stamped metal, add a strip of double-sided tape inside the channel). Deflection Range: 90mm wide to cover the tire's central spray path, with an 18mm rearward overhang. Print Orientation: Drop it flat on its front face in your slicer. The awning prints upwards at an angle, meaning the whole piece prints cleanly with zero supports. Material: PETG or ABS/ASA strongly recommended. PLA will warp from exhaust heat or summer sun.
CandleGuard — Lithophane Shade Core
Introducing CandleGuard, a structural canvas designed specifically for cylindrical lithophanes. Built to sit safely over standard candle bulbs, the design incorporates internal geometry to manage heat and prevent material softening when printed in standard filaments like PLA. Features Thermal Standoff: Six internal ribs maintain a strict 15mm air gap between the lampshade wall and the bulb surface. Litho-Ready: A constant 1.5mm outer shell provides an ideal blank cylinder for applying lithophane textures. Snag-Free Installation: Chamfered rib edges allow the unit to drop smoothly over the lighting fixture without catching. Dimensions Outer Diameter: 80mm Overall Height: 100mm Wall Thickness: 1.5mm
1x6 Toothed Plate
A custom 1x6 building plate combining three 1x2 toothed sections into a single piece. Features a standard 8mm pitch and 3.2mm plate height. Includes 9 teeth arrayed along the front edge. Designed with a hollow underside and clutch cylinders for compatibility.
Lumina — MTB Forward Light Mount_v3
A rugged, modular mounting adapter designed to bridge the gap between mountain bike stems and 35mm lights. Built to sit perfectly flat on the build plate for maximum structural integrity. Features Clears 20mm tight-fit clamping areas Sets your lighting array exactly 50mm forward of the stem center Modular split-clamp design with recessed M4 hardware cavities Beefed-up clamp ears to handle rough terrain without splitting
Cascada — Staggered Desktop Fountain
Cascada introduces a compact, terraced water feature designed to bring a quiet sense of motion to your desk or living space. Staggered square bowls rest on gently chamfered geometric pillars, alternating between a wide blade waterfall and a concentrated U-channel spout. It's built cleanly around a standard miniature 5mm pump setup. Features Alternating Spouts: Each tier drops into the next via a different profile—switching smoothly between a rounded drop-off blade and a semi-circular channel guide. Integrated Routing: A built-in funnel intake at the base connects straight to your pump tube, while a discrete retaining ring holds the top spout securely. Support-Free Tiers: The geometry tapers dynamically under each bowl at a safe 45-degree angle to print safely with zero added supports. Setup Notes Sized for a classic 100mm desktop footprint. Feed a standard 5mm outer-diameter silicone or PVC line from your mini pump at the bottom, through the back channel, and lock it into the top guide loop. Flow levels are tuned to keep roughly 12mm of depth per bowl before spilling over.
Rena Rouge Style Prop Flute
What it's for A stylized prop flute designed for cosplay, featuring a long main staff and a prominent egg-shaped bulb near the top. Both main handles taper inwards where they meet the central bulb to match the on-screen silhouette. Dimensions Overall length: 300 mm Central bulb diameter: 36 mm Main shaft diameter: 20 mm tapering down to 12 mm Assembly Currently designed as separate geometric pieces laid flat for easy modification. For a physical print, you will likely want to merge these into a solid body or add joining pegs between the sections.
Chamfered Heavy Duty Spacer
A 2.5-inch tall solid cylinder spacer with a 1.5-inch outer diameter and a 0.38-inch inner diameter. The inner hole features 1mm chamfered edges at the top and bottom to guide inserted parts and reduce edge stress. Outer Diameter: 1.5" (38.1 mm) Inner Diameter: 0.38" (9.65 mm) Overall Height: 2.5" (63.5 mm) Edge Treatment: 1mm ID chamfers
Wall-Mounted Display Shelf
A sturdy wall-mounted shelf featuring a J-profile design with open sides. Built specifically to support moderate loads up to 2 kg, it includes a generous structural fillet at the rear corner and three countersunk mounting points to distribute weight evenly against the wall. A pronounced front lip keeps displayed items securely in place. Dimensions Overall Width: 240 mm Overall Depth: 80 mm Back Wall Height: 60 mm Front Rim Height: 30 mm Material Thickness: 6 mm Print Notes Prints flat in its natural orientation (bottom surface on the build plate). The integrated countersunk holes are designed to be printed horizontally; they will bridge correctly on most standard FDM profiles without requiring internal supports. Recommended to use at least 3 perimeters (walls) for structural strength. Assembly Mounts directly to a flat surface using three standard flathead or countersunk screws (up to 4.5 mm thread diameter, 9 mm head). Suitable wall anchors are recommended based on the mounting surface to achieve the full 2 kg load capacity.
95mm Topographic Map Coaster Set
A four-piece set of 95mm square coasters that arrange into a single continuous topographic map. Intended as a functional housewarming gift, each piece features recessed grooves along the contour perimeters to capture condensation and prevent runoff. Dimensions: 95mm × 95mm × 8mm per coaster (190mm × 190mm assembled footprint). Contour Geometry: 2mm vertical steps with 1.5mm recessed drip-catch grooves. Base Features: Underside grid pattern provides grip and prevents surface sliding. Spill Containment: Raised perimeter rim captures pooled liquid.
Magnetic Star Chip Cuff
A rigid half-cuff designed for cosplay and collecting, featuring magnetic recesses to hold separate star chips. The cuff is sized to print as two halves that snap together around the wrist using 5x2mm magnets. The star chips are also magnetised, letting you click them in and out of the slots as you earn them. Remix hooks Wrist Fit: Currently set to a 65mm inner diameter with an 8mm wall. Clearance: The star chip is scaled 0.5mm smaller than the recess — scale it in your slicer if your printer needs more or less tolerance. Magnets: All holes are modelled at 5.2mm wide and 2.2mm deep for standard 5x2mm neodymium disc magnets.
Make Me Give A... Sign
A freestanding desk sign that gets straight to the point. The text is stacked and fused together so the whole thing prints as a single solid chunk, anchored by a sturdy underline base. Dimensions: 195mm wide footprint Printability: Prints flat on its back, no supports required.
Lucent — Acrylic Spine Stand
Lucent is a minimalist C-channel spine designed to hold two 1-inch thick, 4x6 acrylic photo blocks in a vertical stack. Rather than encasing the blocks, it grips them from the back using a continuous tension spine and two tiny retention tabs at the extreme top and bottom, remaining almost completely invisible from the front. The entire assembly leans back at a subtle 7-degree angle. Because 2 pounds of solid acrylic has a tendency to tip, the clip features an extended, wedge-shaped rear foot that acts as a counter-lever, keeping the stack firmly planted on your desk. Dimensions Capacity: Holds exactly two 4" x 6" x 1" blocks stacked vertically (8" total height). Clearance: 26.2mm deep slot with a 204.4mm height, allowing the blocks to slide in easily from the side without binding. Footprint: 40mm wide by 75mm deep. Print notes When you import this into your slicer, lay it flat on its side. Printing it sideways ensures the layer lines run continuously along the entire length of the spine. If you print it standing upright, the layers will run horizontally, and the leverage of the heavy acrylics will snap the spine across a layer line. Printed flat, it requires zero supports and is essentially unbreakable.
Sockenlineal für Schuhgrößen
Ein einfaches Messwerkzeug, um während des Strickens die Fußlänge und Schuhgröße einer Socke zu bestimmen, ohne das Strickstück ständig anprobieren zu müssen. Das Lineal wird direkt in die Spitze geschoben. Die eingravierten Skalen in Zentimetern und EU-Größen nutzen sich nicht ab und gleiten glatt am Garn vorbei. Maße und Parameter Länge: 300 mm Messstrecke. Breite: 50 mm, passend für gängige Sockenspitzen. Stärke: 2,4 mm (steif, aber noch nicht sperrig). Skalen: CM oben, EU-Größen unten, nach außen gerückt für bessere Ablesbarkeit.
Split 1U Smart Home Tray
A three-piece split 1U rackmount designed specifically to fit on smaller printers (under 180mm cubed volume). It supports an Adtran 632 ONT and a Home Assistant Yellow side-by-side, while leaving the third tray configured as a 6-port keystone patch panel. Remixing the Rack Space The base design features locking dovetails and bolted structural flanges that securely bridge the three pieces across a standard 19-inch rack. Keystone Spacing: The 6-port patch panel uses standard 14.8 x 16.2 mm cutouts. The wall directly behind them is thinned to 1.5mm so standard keystone clips engage properly without stressing the jacks. Split Points: The joints occur at X = -80 and X = +80. Adjusting these values lets you shift the proportions of the left, centre, and right trays depending on what device combination you want to mount next. Hardware Required: The mating flanges use four M3x16 bolts and matching M3 nuts to pull the dovetail seams tight and handle horizontal shear.
1U Faceplate Tray for Adtran & Yellow
A split 1U rack tray designed to mount an Adtran 632 and a Home Assistant Yellow side-by-side, featuring a full-height 1U front faceplate with custom cutouts so the ports remain visible and accessible. The two halves join in the middle with a dovetail-style jigsaw joint (0.25mm clearance) so it can be printed on standard beds without hardware. Remixing and Adjustments This tray is built to be tweaked depending on the exact dimensions of your enclosures. Adtran Cutout: Sized at 136.5mm wide by 37mm tall. HA Yellow Cutout: Sized at 122mm wide by 33mm tall. Pockets: The internal fences give the devices 1-2mm of breathing room so they slide in smoothly behind the plate. Adjust the pocket blocks if your particular enclosures are bulkier. Joint Tolerance: The 0.25mm puzzle clearance prints nicely on a tuned FDM machine, but can be pushed to 0.15mm if you want a permanent friction fit.
Wide Seashell Glass Tray
What it's for A wide, scalloped catchall tray styled after a seashell. Scaled up specifically to act as a coaster or serving base for two standard drinking glasses. Features a flat base with a prominently flared, rippled rim. Dimensions Base Width: ~210 mm Top Flared Width: ~280 mm Height: 25 mm Wall Thickness: 4 mm Print notes Print flat on its base. No supports are required. A rigid material like PETG or PLA is recommended.
Drawer Hole Cable Catch
Cables yanked back by a retractor will eventually wedge their heads straight into an oversized hole, jamming the spool and leaving you under the desk trying to dig the wire out. This replaces the raw drawer hole with a threaded catch that stops a standard 6x11mm USB-C head dead against the flange. Fit: Threads into a standard 40mm hole on panels up to 8mm thick. Clearance: 5mm center bore lets the cable slide cleanly without snagging. Routing: 4mm side slots let you drop the wire straight in, so you don't have to fish it blindly through the back of the drawer.
40mm Bore USB-C Keyhole Grommet
Mates with a 40mm circular bore in panels up to 10mm thick. Designed for standard USB-C connectors. The geometry allows the connector head to pass entirely through the 16mm offset bore, after which the cable drops into the 6mm central parking hole. The 4.5mm throat prevents the connector from falling back through the panel. Fitment notes Host: 40mm diameter circular hole. Panel thickness: Minimum 1.0mm, maximum 10.0mm. Clearance: The threaded shaft is cut to 39mm outer diameter to ensure bind-free insertion through the panel. Cable head: Clears connector housings up to 15.5mm wide.
Need a part that doesn't exist yet?
Start building →