3D-printable home fixtures & hardware
Brackets, cabinet pulls, knobs, doorstops, racks and mounts built to real measurements. Browse what makers built, or describe the exact fixture you need and Printy makes it.
Need one that fits your exact measurements? Start building →
Newest
83mm Desk Grommet with Sealed Hollow Body
A one-piece desk grommet for an 83 mm hole, with an off-center cable passage. The barrel drops through the desk and the 99 mm flange rests on the surface; 3 mm caps close the part at both ends and the interior is a sealed hollow, so it uses little filament for its size. A 14 mm cable hole sits 30 mm from the center, about 4 mm in from the rim, and passes through the flange and both caps. It takes most round power cables but will not pass a plug. Desk hole: 83 mm Barrel: 82.6 mm outside diameter, 20 mm tall Flange: 99 mm diameter Cable hole: 14 mm diameter, 30 mm from center, near the edge Wall and cap thickness: 3 mm; cable-hole wall: 2 mm Interior: sealed hollow cavity Fit: desk tops up to about 17 mm thick Print: one piece; no external supports; the enclosed cavity will bridge internally near the top of the void Overall footprint on the plate: 99 × 99 × 20 mm
CrestHook — 80 mm D-Ring S-Hook
CrestHook is an 80 mm S-hook made to bridge a D-ring and whatever needs hanging from it. Two opposing round hooks share the same crest-to-crest length, and each end has a 20 mm opening intended to clear a typical D-ring bar with room to spare. The hook is laid flat for printing, so the layers follow the curve rather than crossing it. Dimensions Overall footprint: 58 × 80 × 8 mm on the print plate Length: 80 mm crest to crest Hook opening: 20 mm at each end Wire section: 6 mm thick × 8 mm tall Print orientation: lies flat on the plate
10 mm Bore Screw-Together Coupler
Złączka skręcana z zaciskiem, w trzech rozmiarach: na rurkę lub pręt 10 mm, 8 mm i 6 mm. Każdy zestaw to dwie drukowane części — część z gwintem zewnętrznym ma cztery szczeliny tworzące sprężyste palce, a nakrętka ma w dnie stożek. Dokręcanie nakrętki nasuwa stożek na skosy palców i zmniejsza otwór, więc złączka zaciska materiał zamiast tylko go przepuszczać. Korpus, sześciokąt i gwint 16×2 mm są takie same we wszystkich trzech rozmiarach. Zmienia się tylko otwór oraz stożek zacisku w nakrętce. Dopasowanie Host: zwykła okrągła rurka lub pręt o nominale 10, 8 albo 6 mm. Otwór w spoczynku: 10,5 mm / 8,5 mm / 6,5 mm. Gwint: 16 mm średnicy zewnętrznej, skok 2 mm; pasuje tylko do nakrętki z tego zestawu. Korpusy: sześciokątne, do klucza. Montaż: dwie drukowane części na rozmiar, skręcane razem. Zamienność: korpus i gwint są wspólne, ale stożek w nakrętce jest dobrany do rozmiaru — do prawidłowego zacisku używaj pary z tego samego zestawu. Sprawdź przed drukiem Zmierz rzeczywistą średnicę zewnętrzną rurki lub pręta. Materiał większy niż nominalny albo żebrowany nie wejdzie do otworu; materiał mniejszy może nie zostać zaciśnięty. Dokładna wartość zmniejszenia otworu podczas dokręcania nie jest sprawdzona w druku, więc przetestuj zacisk na złomowym materiale. Przy 6 mm palce zaciskowe są grubsze, więc zacisk jest sztywniejszy i może wymagać mocniejszego dokręcenia. Nie pasuje Gwint M10 ani pręt gwintowany; to otwór na gładki materiał, nie połączenie gwintowe. Standardowe gwinty rurowe metryczne lub BSP; gwint 16×2 mm jest specyficzny dla tej pary. Złączki do węża. Zastosowania ciśnieniowe; drukowany gwint nie tworzy uszczelnienia. Mieszanie rozmiarów: zestaw 10 mm nie jest do rurki 8 mm ani 6 mm, a zestawy 8 mm i 6 mm nie przyjmą rurki 10 mm.
Four-Bay Workshop Study Table
A utilitarian steel-and-ply desk in the spirit of a workshop bench: a 54 × 36 × 30 in frame of 1-inch square pipe, split into four side-by-side bays along its length, topped with 12 mm plywood. The lower frame forms a U (back and both sides) so a chair slides straight in from the front. Layout Dividers across the width: 8 mm round bar at 1/4 length, 1-inch square pipe at centre, 8 mm round bar at 3/4 length. Small flat tabs on the round bars give the plywood something to screw into. Legs 750 mm, lower rails 150 mm above the floor. Pipe wall thickness (1.6 mm) is an assumption and needs checking on the actual pipe.
20 mm Round Hollow Pipe, 136 mm Long
A round hollow pipe with a 20 mm outer diameter, a 16 mm bore and an even 2 mm wall, 136 mm long and open at both ends. It serves as a sleeve, spacer or bushing stock, or as a straight run in small frames, racks, handles and standoffs. At 136 mm it prints as one piece on a common print bed, with the length running along the plate. Specs Outside diameter: 20 mm Bore: 16 mm, centered Wall thickness: 2 mm, even all round Overall length: 136 mm Both ends open, full length through Rests on the build plate with the length along the plate Printing notes 136 mm length fits standard beds without splitting into segments. Vertical orientation needs no support inside the bore; horizontal orientation holds truer round but needs support in the bore. The bore is centered, so the wall is even all round where concentricity matters.
Pay For Photos At Till Sign
A "Please pay for photos at the till" sign for counters and shop windows, where customers walk off with prints without paying. Raised white lettering on a flat blue plate reads clearly from a distance. Print details Plate: 160 × 60 × 8 mm, rounded edges Lettering: two lines, raised 1.2 mm from the front face Print flat on its back; switch filament for the letters, or paint them No supports needed Attach with double-sided tape or foam pads
Vileda Broom Bar Hook
A bare metal broom top snags on everything, and the mushroom-shaped anchor on a Vileda stick gives a plain hook nothing secure to grab. This replacement end cap sleeves 20 mm down over the sharp top of the stick, then snaps over the anchor on four flexing collet fingers with locking pads. The open hook sits centered over the sleeve so the broom hangs straight on a 27 mm bar, and the flared mouth catches the bar without needing perfect alignment. Fit and print Broomstick: fits a 25.3 mm Vileda stick; the sleeve drops 20 mm over the sharp top edge. Anchor: clears the 13 mm mushroom cap and locks around the 10 mm shaft. The four fingers are 3 mm at their weakest point and taper to 4.5 mm at the base, with a 24 mm relief void and 2 mm slits so they splay outward without binding. Hook: open downward U-channel for a 27 mm bar, not a closed loop; the flared mouth funnels the bar in. Wall: solid plastic separates the flex mechanism from the hook cavity, and the hook sits raised clear of the flex chamber. Printing: lay the 2 mm flat plateau on top of the arch on the bed and print upside down — no supports, the internal ceiling bridges. Feel: the thicker fingers take a firmer push to seat, and hold once they do. Size: 31 mm wide, 63.5 mm deep, 118 mm tall as oriented for printing.
Veranda End Railing Bay
A single-span railing bay for the short end of the veranda, with a post at each corner, a top rail, a lower rail and vertical pickets spaced about 110 mm apart at full scale. One continuous bay with no centre post Pickets run only between the lower and top rails Posts sit flat at deck height for gluing onto the deck Same scale and position as the other veranda files, about 140 mm wide at print size
Wall Shelf for Lamps and Small Decor
A lamp with nowhere to stand but the windowsill, a handful of small things spreading across the desk, and a shelf that dips the moment you put any weight near its edge — this wall shelf fixes that by being thick enough not to care. The slab is a solid 300 × 140 × 25 mm block that projects forward from the mounting plate, carried on two 50 mm supports underneath so the front edge stays level when you set something down on the end of it. Nothing on the shelf surface to snag on or route around: it's a flat slab with clear space above it, so a lamp base sits flush and a row of small items lines up without wandering. Mounting Back plate is 300 × 20 × 140 mm, sitting flat against the wall behind the slab. Two countersunk screw holes in the plate, above the shelf line, so the heads finish flush and nothing catches on them. Fix into studs or proper wall anchors — the printed mass plus a lamp is real weight hanging off the wall. Printing The shelf body and back plate are labelled as separate areas, so you can run them in different colours for a concrete-and-shadow look. The chunky sections want a few walls and moderate infill rather than solid — you're after the mass, not the plastic bill. The slab itself prints without supports.
White 4 x 10 Inch Flat Vent Grill
Flat slotted vent grill, 10" x 4" with a thickness of 1/4". Two banks of eight through-slots are separated by a center rib for stiffness, inside a solid border. Size: 254 x 101.6 x 6.35 mm Slots: 8 per side, 5 mm wide, 112 mm long, rounded ends Border: about 10 mm solid on the long edges, 15 mm on the ends Print flat, no supports; PETG or ASA suits warm airflow Edges: 4 mm rounded vertical corners
Holdfast — Curtain Rod Wall Bracket
Holdfast is a single-piece wall bracket for a 28 mm curtain rod. A flat 60x60 mm plate carries a 100 mm arm that ends in an open-top half-round cradle, so the rod drops in from above. A small set screw hole through the front wall of the cradle lets the rod be locked in place once seated. The cradle is sized at 28.5 mm inside diameter, giving a snug fit around a 28 mm rod without binding. The arm is kept compact and the cradle walls are thick enough to carry a set screw. Features 60 x 60 x 5 mm wall plate with chamfered edges Four countersunk screw holes (4.5 mm) for flush mounting 100 mm arm projecting from the plate 28.5 mm half-round cradle, open on top for drop-in rod loading 4.2 mm set screw hole through the cradle, level with the rod centre Print notes Tap the set screw hole by hand or use a self-tapping M4/M5 screw. Print with layers running along the length of the arm, since the arm is only 12 mm thick and works under leverage. Use PETG or a similarly tough material for load-bearing use. Parts Wall Plate Arm and Cradle
12V-Stabschiene 6 mm Klemmplatte für Ø80 Spot
Zweiteilige Trägerplatte für einen runden 220V-Spot mit 80 mm Basis auf einem 12V-Stabsystem: zwei parallele Stäbe Ø6 mm, 35 mm Mitte zu Mitte. Die Oberplatte trägt den Spot, die Unterplatte klemmt die Stäbe von unten dagegen. Passt auf Zwei Rundstäbe Ø6 mm, Abstand 35 mm Mitte zu Mitte (Nuten Ø6,3 mm) Runde Spotbasis Ø80 mm (Senkung Ø80,4 mm) Passt nicht auf Stäbe mit anderem Durchmesser oder anderem Abstand Spots mit abweichendem Lochbild: angenommen sind drei Löcher Ø4,5 mm auf Lochkreis 60 mm Vor dem Drucken prüfen Lochbild des Spots und Stabdurchmesser nachmessen. Montage Sechs Schrauben M4 von unten durch die Unterplatte (Senkung für den Kopf) in die Oberplatte; Bohrung Ø3,4 mm schneidet das Gewinde selbst. Kabeldurchlass Ø14 mm in der Mitte. Beide Teile liegen mit offenen Nuten nach oben auf dem Druckbett, ohne Stützen. Ein 220V-Spot an einer 12V-Schiene braucht eine saubere elektrische Trennung. Das Druckteil ersetzt keine Schutzisolierung.
70 × 108 × 25.5 mm Box Snap-Clip Frame
Snap-clip mounting frame for a 70 × 108 × 25.5 mm box, with two 20 mm clips joined by a lightweight frame. Fit Clips sit 108.6 mm apart, inside to inside. Four 20 mm corner blocks locate the box sideways, with 0.3 mm of play per side. Three countersunk screw holes: one in each clip flange and one at the center. Check before printing Confirm the box measures 70 × 108 × 25.5 mm. It does not suit other sizes without changing the clip spacing and block positions. Structure The frame is 3 mm thick. It uses two edge rails, three crossbars and a center screw pad, and prints flat on its back.
Pool Noodle End Cap Plug
A pool noodle end cap that plugs the hole so water, sand and grit stay out of the foam, and the open end stops getting chewed up. The plug uses the same barbed shaft as the noodle connector, so it grips the foam instead of working loose. Key numbers Shaft: 22 mm diameter, 56 mm long, tip chamfered for easy starting Barb rings: four, 28 mm diameter, 14 mm apart, chamfered both sides Head: 70 mm diameter, 8 mm thick, rounded top edge, stops flush against the noodle end Sized for a roughly 25 mm centre hole; foam stretches over the rings Printing Print head-down on the plate, shaft pointing up No supports needed, the ring chamfers handle the overhang PETG or similar; 3 perimeters for stiffer barbs
12 V Solenoid Water Valve
Normally closed 12 V DC water solenoid valve (0.6 A, 1/4-inch ports, 0–8 bar reference rating, pending manufacturer confirmation) for a smart tap attachment. Shown as a half-section so the flow bore, seat chamber and plunger are visible, with a green flow-direction arrow on the front face. Remix hooks Port interface: portthreadd (13.2 mm, 1/4" BSP major diameter), portbored (8 mm), portlen (14 mm) and portod (19 mm). Match these to the purchased valve. Body size: bodyl 40 × bodyw 24 × body_h 26 mm. Coil: coild 30 mm, coilh 38 mm. Cutaway: set cutaway = false for the full solid view. Terminals: two 2 mm blade tabs at 10 mm spacing (term_sp). Mounting: two Ø4.2 mm lugs on the front at 20 mm spacing. Move or add lugs for a different bracket. Pairs with: a tap-adapter bracket, a relay or MOSFET driver board, or a flyback-diode cover. This is a visual and fit-check reference, not a flow-tested part. Thread forms are plain bores.
30° Ceiling Vent Air Deflector
A clip-on deflector for a 10 x 10 cm ceiling vent. A blade tilted 30° redirects cold air sideways across the room instead of straight down onto a desk. Four spring tabs grip the vent edges and flex over a 5 mm thick lip. What it's for Redirects airflow from a square ceiling vent away from a desk or seat. Mounts without screws or adhesive: the four tabs snap over the vent lip. The blade spans the opening at a fixed 30° angle. Dimensions Frame: 108 x 108 mm outer, 96 x 96 mm opening, 3 mm thick. Spring tabs: four, one per side, 16 mm wide, with a 5.4 mm gap under the hook for a 5 mm lip. Tabs reach about 10.4 mm above the frame base. Blade: 96 mm wide, 2.4 mm thick, tilted 30°. Overall height is about 22.6 mm. Assumes a 100 x 100 mm vent opening with the frame sitting around it. Print notes PETG is the better choice, since the tabs flex and PLA is more likely to snap. Print the frame flat, with its base on the bed. Check the lip thickness on your vent. Adjust the tab gap if it is not 5 mm. Remix ideas Change the blade angle for a steeper or shallower sweep. Make the tabs wider or thicker for a firmer grip. Resize the frame for a different vent size. Add a second blade to split the airflow in two directions.
Diskokugel-Adapter mit Deckenlaschen und M4-Gewinde
Der Sockel der Diskokugelhalterung hat keine Möglichkeit, direkt an der Decke zu hängen, und passt nur mit Schrauben an der Unterseite. Dieser Adapter löst beides: ein Zylinder, der unten an die Halterung geschraubt wird und oben innen sechs Laschen für die Deckenschrauben hat. Maße und Druck Zylinder: 130 mm Außendurchmesser, 3 mm Wand, 50 mm hoch Unterer Innenrand: 10 mm breit, 4 mm dick, Öffnung 110 mm Vier M4-Gewinde (30 mm tief) auf 123 mm Lochkreis, in Domen mit 11 mm Durchmesser Sechs Deckenlaschen: 24 × 18 × 4 mm, 4-mm-Loch, bündig mit der Oberkante, im Abstand von 60° Druck: Öffnung nach unten, ohne Stützen, PETG oder ASA empfohlen
Open-Side Curtain Rod Bracket revB
A round curtain rod bracket for a 1" rod: a 35 mm base disc with a countersunk centre screw hole, topped by an 18 mm collar with a 29 mm bore. One side of the collar is open so the rod slides in sideways, and a round set-screw hole in the opposite-facing wall locks it in place. Remix hooks Bore (29 mm): a 1" rod is 25.4 mm, so 26 to 27 mm gives a snugger fit. Opening width (26 mm): narrow it to about 22 mm for a snap-in grip, or widen it for easier loading. Opening direction: currently on +X, 90° from the set screw. Rotate it to suit the mounting position. Set-screw hole (4.5 mm): resize for M3, M4 or M5 hardware, or add a nut trap. Collar height (18 mm) and base thickness (3 mm): change for more grip or a sturdier mount. Pairs well with a matching bracket at the other end of the rod.
Cardboard Sign Corner Holder for Wall
A cardboard sign corner holder that ends the problem of taping or tacking a sign to the wall. The triangular pocket slips over a corner of 3 mm cardboard, like a photo corner, and the flat back takes a removable adhesive pad. Slot height: 3.4 mm for 3 mm cardboard Leg length: 40 mm per corner Back plate: 2 mm, flat side faces the wall Front lip: 1.6 mm, with a cut-out window Print: flat on the back, no supports, one per corner (4 for a sign)
Tapered Tunnel Adapter 20x23 to 19x19
A short tapered sleeve for a hole that is too big or the wrong shape for what goes in it. This one is 7 mm long with thin 0.6 mm walls, so it slips in without eating the opening. Key numbers Large end outer size: 20 x 23 mm Small end outer size: 19 x 19 mm Length: 7 mm Wall thickness: 0.6 mm Open all the way through Printing Print standing on the large end, no supports needed Walls are about 1-2 nozzle widths thick, so use a 0.4 mm nozzle and 1-2 perimeters No clearance is added; scale slightly if the hole is tight
Y-Rohrstück 75 auf 39 mm mit Steckende
Y-Rohrstück, bei dem ein weiteres Rohr auf dem oberen Ende nicht richtig sitzt, weil kein gerades Stück zum Aufstecken vorhanden ist. Der obere Abschnitt hat jetzt ein 20 mm langes gerades Ende mit 39 mm Außendurchmesser. Unterer Teil: 75 mm Außendurchmesser, 30 mm lang Konus: 30 mm lang, von 75 auf 39 mm Steckende oben: 39 mm Außendurchmesser, 20 mm lang Abzweig: 39 mm Außendurchmesser, 48° zur Rohrachse, schneidet die obere Öffnung nicht Wandstärke: 2 mm überall Druck: aufrecht auf der 75-mm-Öffnung, der Abzweig braucht Stützen
Veil — Air Freshener Front Plate
Veil is a plain, flat front cover for an automatic air freshener dispenser. It is a clean blank with rounded corners, ready to be used as-is or modified with cutouts for a nozzle, sensor or window. Dimensions Height: 230 mm Width: 76 mm Thickness: 1 mm Corner radius: 8 mm Print notes Print flat on the bed, no supports needed. At 1 mm thick, a wide brim or a slow first layer helps prevent warping.
Advent Calendar Drawer With Grip
A single replacement drawer for an Advent calendar: open-top box, 41.5 × 23.5 × 44 mm, 1.5 mm walls and floor, with the number engraved on the front above a small square grip. Remix hooks Grip size: 8 × 5 mm face, 4 mm projection (5 mm deep body, 1 mm embedded). Make it wider for easier pulling. Grip rounding: 0.8 mm edge rounding. Raise it for a softer look, drop it for a sharper square. Number: 8 mm Roboto, engraved 1 mm deep near the top. Change the digit for other drawers. Fit: trim 0.2 mm off width and height if it binds in the frame. Pairs with: the other numbered drawers, since the front footprint is unchanged.
Wall Shelf, 20 cm Glue-On
A small wall shelf that sits flat against the wall and glues on, with no drilling and no screws that miss the stud. The tall back plate gives the adhesive a big flat face, and two triangular gussets stop the front edge from sagging or peeling off. Key numbers Shelf top: 200 mm long x 80 mm deep x 4 mm thick Back plate: 200 x 40 mm, 4 mm thick, flat on the wall side Two gussets, 4 mm thick, each 34 mm tall Print: shelf upright on its back plate or flat on the top, no supports needed with the plate down; PETG or PLA, 3+ perimeters Glue: construction adhesive or mounting tape on the back plate face
Need a part that doesn't exist yet?
Start building →