3D-printable storage & organizers
Boxes, wallets, dispensers, holders and carriers sized for real contents. Browse what makers built, or describe the exact organizer you need and Printy makes it.
Need one that fits your exact measurements? Start building →
Newest
220x140x120 mm Square-Bar Storage Frame
Rectangular storage stand made entirely of solid 15 × 15 mm square bars. Two rectangular frames, top and bottom, are joined by four corner posts. A single reinforcing beam runs across the width at the middle of the top frame. All edges are sharp and all faces are flat, with no fillets or curved surfaces. Outer size: 220 mm long × 140 mm wide × 120 mm high Bar section: 15 × 15 mm, solid Posts: four, at the corners, 90 mm visible length between frames Top beam: 15 mm, centred along the length and spanning the width Print: flat bottom face on the bed, no supports needed for the main frame; the top beam spans 110 mm, so expect minor bridging sag Single welded body, symmetrical about both vertical centre planes
Spanline — Three-Part Bookshelf Riser
Spanline is a bridge-shaped bookshelf riser, 450 × 125 × 125 mm when assembled, split into three sections that each fit a 200 mm print bed. Sliding dovetail joints lock the sections together, and the tunnel underneath stays open for storage. Print layout Three separate pieces, spaced 20 mm apart, none touching. Each piece is flipped so the flat top face sits on the bed, so no supports are needed for the arch. Each piece is about 162 mm long, including its dovetail tongue. Features 16 mm top and walls with a 25 mm rounded inner arch Dovetail tongue-and-groove joints with 0.25 mm clearance Shallow rib under the top of each section Assembly Slide Part B onto Part A's tongue from the side, then slide Part C onto Part B's tongue.
peterson 80x95 v3
sdf
Petersson 95x80 v2
A 95 × 80 mm open-top tray, 50 mm tall, with 2 mm walls and a 2 mm floor. What it has 1.5 mm chamfers on the bottom edges and vertical corners; the top rim stays square. Four triangular corner gussets at the rim (z 47–50 mm), each with a 6.1 mm pocket 2.1 mm deep. A 44 mm long, 45 mm tall cut-out in the centre of the -X wall, leaving a 5 mm bottom lip. 13 vertical grooves (2 mm wide, 0.8 mm deep) on the outside of the +X wall. Check before printing The cut-out is 44 mm long so it stays clear of the gussets. Wider cut-outs would cut into them. Does not fit The earlier 155 mm length is gone; the tray is now 80 mm long.
Modular Ribbed Shoe Shelf Insert
What it's for A freestanding shelf insert for a 260 × 300 mm wardrobe compartment, sized for children's shoes. It stands on the shelf below with no drilling and no fasteners. The deck is a light ribbed grid in four staggered panels. Each panel fits a small printer bed. Dimensions Assembled deck: 258 × 290 mm, 10 mm deep, top surface 130 mm above the floor. Deck panels ×4, brick-bond layout so no point has four panels meeting: Front left: 150 × 145 mm Front right: 108 × 145 mm Back left: 108 × 145 mm Back right: 150 × 145 mm Legs ×4: 28 × 28 mm foot, 20 mm cross-section post, 120 mm tall, plus a 12 mm square locating peg that is 10 mm long. Dovetail keys ×4: bow-tie shape, 24 × 11 mm, 9.6 mm thick. Estimated material: about 130–140 cm³ in total. That is roughly 85–95 cm³ for the deck, 45 cm³ for the legs and 2 cm³ for the keys. Assembly Drop a bow-tie key into the paired pockets across each seam. There are 0.2 mm clearances per side. Press each leg peg into the socket in its corner of the deck. Each leg sits in a different panel, and the peg sockets stop the deck sliding or racking. Add felt or a thin TPU pad under the feet if desired. Print notes Print every part flat or upright with no supports, using PLA and a 0.4 mm nozzle. Keep the legs peg-up. Remix ideas Add a front lip to stop shoes sliding out. Swap the cross-section legs for taller ones to suit other compartments. Make the ribs denser for heavier loads.
Runder Deckel für Spiderlingsbox mit Futterluke
Der Deckel der Spiderlingsbox hat eine Futterluke, deren Stopfen sich beim Umdrehen oder Anstupsen nicht löst. Der Stopfen wird eingesetzt und um 45° gedreht, bis die drei Stifte in den Nuten hinter dem Ring sitzen. Deckel: 103,6 mm Außendurchmesser, passend für 99 mm Box, 2,8 mm Lippe, Rastnasen am Rand Luke: 20,4 mm Loch, Ring mit 3 mm Wand drumherum Stopfen: 19,8 mm Schaft, drei Stifte (1,8 mm) im Abstand von 120°, Griffnase zum Drehen Druck: Deckel mit Top- und Bottom-Layer 0 für das Gitter. Stopfen mit Flansch nach unten, normale Einstellungen.
Apothecary Box With Lift-Off Lid
A classic apothecary-style storage box, 6" x 4" x 2", with a separate lid whose inner lip plugs into the body. The two pieces are laid out side by side for viewing and print as two separate jobs, so each fits an 18 x 18 cm bed. Body: 152.4 x 101.6 x 47.5 mm, 2.4 mm walls, chamfered edges Lid: 152.4 x 101.6 mm, 3 mm plate with a 5 mm plug lip Fit: 0.3 mm clearance between lip and body recess Print the lid flat with the lip facing up, no supports needed
Drawerling — 115 x 150 Desk Drawer Bin
Drawerling is an open-top rectangular bin sized for a desk drawer, built to exact external dimensions of 115 × 150 × 60 mm. Straight walls, a solid floor and softly rounded vertical corners make it easy to wipe clean and print without supports. Dimensions External: 115 mm wide × 150 mm deep × 60 mm high Walls: 2 mm Floor: 2 mm, solid Corner radius: 4 mm (vertical edges) Features Fully open top, no lid, hinges or handles Flat base for support-free FDM printing Single watertight body, STL-ready
Sliding Lid iPhone 11 Box
A two-piece protective box for an iPhone 11. The base holds the phone; a flat lid slides in from one end along grooves cut into the long walls, with a round thumb slot to push it open. Remix hooks Cavity: 154 × 79 × 13 mm open space (phone is ~151 × 76 × 8.3), 2 mm walls and floor. Change the cavity numbers for other phones. Groove fit: grooves are 1 mm deep and 2.2 mm tall, lid is 2 mm thick, about 0.2 mm clearance each side. Tune for your printer. Thumb slot: 16 mm diameter at the open end; make it larger or swap for a slot. Pairs with: a foam or felt liner, or a detent bump to stop the lid sliding open. Print both pieces flat, no supports needed.
C Clip for 9V Battery Container
What it's for A snap-in C clip that holds a 22 x 33 mm 9 V battery container. The opening sits in the front long wall, so the container presses in and pulls out when the battery needs changing. Dimensions Inside pocket: 22 x 33 mm Height: 20 mm Wall thickness: 2.5 mm Opening: 27 mm wide, leaving 3 mm of retaining wall on each side Outside: 38 x 27 mm Remix ideas Widen the opening to 28 or 29 mm for an easier release. Add a mounting tab or screw holes on the back wall. Print in PETG or nylon for better flex at the snap.
Organizador gloss
Organizador de gloss com estética de penteadeira rosa: um bloco baixo com 10 furos em grade 5x2, o nome "Laura" em relevo na frente e dois pequenos corações rosa, um de cada lado do nome. 10 furos de 22 mm de diâmetro Nome e corações em rosa mais forte que o corpo Corações em relevo, sem suportes Fácil de trocar o nome ou a quantidade de corações
Mister Box Holder with Open Front
A wall-mounted cradle for a 2.25" x 4.75" x 2" mister box, sized with extra width clearance and a little extra depth so the box slots in easily but can't tip forward out of it. The front is open below a solid top rim so the buttons stay reachable, and a low lip along the bottom front edge holds the box in. Two identical ears on the back face carry countersunk screw holes for mounting to the side of furniture. Full 4.75" (120.65 mm) wall height 10 mm width gap, 3 mm depth gap Cord notch in the left rim only, 15 mm wide, centered 1.5" from the inside back wall, open at the top Window cutouts on the sides to save filament Two back ears with countersunk screw holes
3×2 Fächergitter 40×40 mm, 60 mm hoch
Fächergitter mit sechs durchgehenden Schächten (3 nebeneinander, 2 hintereinander), oben und unten offen. Gedacht als Sortier- oder Einsatzraster für Teile, die in einen 40 × 40 mm Schacht passen. Maße Fach innen: 40 × 40 mm Höhe: 60 mm Wände: 2 mm, auch zwischen den Fächern Außenmaß: 128 × 86 × 60 mm Steg: umlaufender Rand bei 20 mm Höhe, 2 mm dick, 5 mm breit; Öffnung dort 30 × 30 mm Vor dem Drucken prüfen Der Steg ist eine Annahme: ein umlaufender Rand in jedem Fach. Ein Teil, das durch das Fach muss, braucht Platz im 30 × 30 mm Durchlass. Passt nicht Gegenstände über 30 mm Breite passen nicht durch die Stegöffnung.
Caregiver Check Station Enclosure, Gray and Red
A caregiver check-in box with no obvious place to tap, and a back panel that fights you at every repair. This enclosure puts a large red TAP HERE panel on the front and a screw-on back cover behind it, so the electronics come out without disturbing the front. Size: 150 × 110 × 36 mm body, with a 3 mm back cover. NFC panel: 64 × 64 × 2 mm red panel, replaceable, behind a 1.5 mm lip. It is held by a separate holder with four M2.5 screws. Back cover: four M3 × 12 screws into body posts, with a 0.3 mm clearance skirt. Two keyhole slots handle wall mounting. Openings: PIR window 23 mm, three 5 mm LED holes (green, yellow, red), BME280 air slots, 12 × 6.5 mm USB-C slot, 5 mm reed-switch cable hole, and top and bottom vent slots. Printing: body and panel face-down, cover outside-down. PLA, no supports, 3 walls, about 15% infill. Not final: every board position is a placeholder. Measure the ESP32, PN532, PIR and BME280 before fixing the internal layout.
Tabletop Wildlife Alert, 100 mm Diamond Sign
Modular tabletop wildlife-warning prototype printed as separate parts that bolt together: base, three pole sections, four brackets, electronics enclosure with lid, PIR sensor housing with rain hood and lid, amber light housing with lid, and a diamond sign reading WILDLIFE CROSSING with no graphic. The stack runs bottom to top: electronics enclosure, PIR sensor facing forward, two amber LED openings, then the sign. Each housing screws to its own bracket, and each bracket clamps onto the pole with one cross-screw. Dimensions (mm, outside) Electronics enclosure: 70 × 60 × 50, interior about 65 × 57 × 45, with lid PIR housing: 60 × 40 × 35, 23 mm lens opening, rain hood, with lid Light housing: 70 × 35 × 30, two 8 mm LED openings, with lid Sign: diamond 100 point to point, 3 mm thick Base: 100 × 84 × 6 Pole: three sections, 20 × 20 × 58 Overall height: about 224 To confirm before printing Controller board size (a full Uno will not fit the interior) PIR lens diameter and LED diameter (23 mm and 8 mm are placeholders) Printer build area Electronics are untested
Tabletop Wildlife Alert, 100 mm Diamond Sign
Modular tabletop wildlife-warning prototype printed as separate parts that bolt together: base, three pole sections, four brackets, electronics enclosure with lid, PIR sensor housing with rain hood and lid, amber light housing with lid, and a diamond sign reading WILDLIFE CROSSING with no graphic. The stack runs bottom to top: electronics enclosure, PIR sensor facing forward, two amber LED openings, then the sign. Each housing screws to its own bracket, and each bracket clamps onto the pole with one cross-screw. Dimensions (mm, outside) Electronics enclosure: 70 × 60 × 50, interior about 65 × 57 × 45, with lid PIR housing: 60 × 40 × 35, 23 mm lens opening, rain hood, with lid Light housing: 70 × 35 × 30, two 8 mm LED openings, with lid Sign: diamond 100 point to point, 3 mm thick Base: 100 × 84 × 6 Pole: three sections, 20 × 20 × 58 Overall height: about 224 To confirm before printing Controller board size (a full Uno will not fit the interior) PIR lens diameter and LED diameter (23 mm and 8 mm are placeholders) Printer build area Electronics are untested
Hex-Embossed Storage Tub
This storage pot brings an industrial, sci-fi crate aesthetic to the workshop or pantry desk. The model measures exactly 145mm wide, 200mm long, and 100mm deep on the inside, leaving plenty of room to slot in boxed goods or bulk packaging. Design Notes Textured Shell: The outer walls feature a debossed hex-grid pattern that improves grip without compromising wall strength. Grip Handles: Both ends feature pill-shaped cutouts scaled for easy lifting, whether it's on a high shelf or tucked under a bench. Rounded Profile: Corners are filleted inside and out, making the tub easy to wipe down.
Caixa 120x120x50 mm Estação Meteorológica
Caixa quadrada de 120 × 120 × 50 mm com paredes de 2 mm e tampa separada, fixada por quatro parafusos M3 nos cantos. Possui abertura para display, chave gangorra, entrada USB-C e fendas de ventilação, além de duas fendas para alça na parte superior da lateral. Parafusos: 4 colunas de canto, furo de 2,8 mm na base e 3,4 mm com escareado na tampa Display: abertura de 24,4 × 14,4 mm na tampa Chave gangorra: abertura de 15,3 × 10,3 mm na tampa USB-C: abertura de 9 × 4 mm na lateral +X Alça: duas fendas de 16 × 4 mm no alto da parede +Y, a 30 mm do centro para cada lado Ventilação: fendas nas laterais, longe das colunas, com fendas extras na região dos sensores Protoboard: dois trilhos baixos no fundo como guia provisório Impressão: base e tampa separadas, sem suportes necessários
Four-Deck UNO Vault With Cap
A card-table caddy for four UNO variants: Classic, No Mercy, All Wild and Flip. Each deck lies flat in its own slot, split by 2 mm dividers, and a slip-over cap closes the box so nothing shuffles between slots. Slots sized from the supplied card dimensions plus clearance Walls 54 mm tall, so the tallest deck stays below the rim Finger hole through the floor of each slot to push decks up Front scoops for gripping Cap prints upside down and fits snugly over the outside of the rim
Stackable 20° Tilt Stand, Print Twice
A single 160 mm cylindrical half, cut on a 20° plane, that is printed twice. One piece alone holds a 120 mm cylinder tilted 20°. Two pieces, one flipped onto the other, stack into a straight block. Quantity: print 2 identical pieces. Seat: 124 mm diameter, 10 mm deep, on the tilted face. Lip: 175° arc, 7 mm thick, 15 mm tall, radius 62 to 69 mm. Step: 185° arc with 1.5 mm clearance per side and a 3 mm chamfered edge. Handles: three 30 mm finger scoops, 3 mm deep. Fit: slip fit, no snap. Bed size: at least 160 mm.
Inverted Glue Bottle Stand
Keep viscous liquids like glue or ketchup primed and ready at the nozzle. Storing bottles inverted ensures immediate dispensing, eliminating the wait for a half-empty bottle to drain toward the cap. The stand is designed with a stable tripod base and precise clearances to hold the bottle securely while catching any rogue drips. Design specifications: Sized to cradle a 45mm bottle body Integrated 30mm drip cup positioned directly under the nozzle Beveled entry ring guides the bottle smoothly into place Tapered support arms print cleanly without support material Wide footprint prevents tipping even with a full, top-heavy bottle
Sliding Tray With Lid Handle
A 78 x 47 x 125 mm vertical tray that slides into a box, topped by a lid that doubles as a pull handle. Four compartments, lowered front lips and a grooved finger tab make loading and pulling easy. Remix hooks Wall and floor: 1.2 mm walls, 1.8 mm floor. The floor absorbs the leftover height so the 56 mm lower row and 66 mm upper row fit the 125 mm total. Lip height: 6 mm front lips with a 22 mm round dip. Raise the lip for deeper pockets, or widen the dip for bigger fingers. Dividers: the vertical wall sits at 38 mm from the left, and the right side is split by a horizontal wall. Move either to resize the compartments. Ribs: 2 x 2 mm guide ribs on the side walls, full height. Change them to match the clearance of the box. Lid: 90 x 56 x 8 mm, flush at the back, with 45 degree chamfered underside edges and three 1 mm grooves on the 30 mm tab. Pairs with any box sized around the 82 mm tray. Prints upright with no supports.
Drawer Sleeve Box With Mounting Pad
Open-top rectangular sleeve, 86 x 52 x 127 mm, for a sliding drawer. Smooth interior, 1.6 mm floor, sides and front, 2.4 mm back wall. A raised 40 x 40 x 3 mm pad on the back carries two M3 nut traps. Remix hooks Pad position: top edge sits 10 mm below the rim; pad is centered in X. Move or resize freely. Nut traps: 5.7 mm hex, 2.5 mm deep, 25 mm apart, with 3.4 mm blind holes behind them. Blind holes stop 0.8 mm short of the inside; thicken the back wall to go deeper. Edges: 3 mm vertical rounding, 6 mm 45° bottom chamfer (prints without supports). Drains: two 3 mm holes at X = ±20 mm. Pairs with a matching drawer 3 to 4 mm smaller in each direction.
Gaveta Vertical Mini APH Pocket
Uma gaveta vertical de bolso, no espírito de um canivete suíço de primeiros socorros: o puxador largo no topo é também a tampa, e puxá-lo para cima faz a bandeja subir pelas guias, expondo os itens. Notas de projeto Corpo 86 × 52 × 127 mm, parede de 1,6 mm, dois drenos de ø 3 mm e furo de ø 4 mm para cordão. Bandeja 78 × 47 × 125 mm com tampa de 90 × 56 × 8 mm, recorte de dedo e divisórias. Clipe em J de 40 mm, 2,6 mm de espessura, impresso deitado. Pensado para PETG, sem suportes. Versão simplificada: dentes de retenção, rabo-de-andorinha, berço do oxímetro e batente liberável ainda não modelados.
Need a part that doesn't exist yet?
Start building →